Rockchip RK628 For-All: vollständige Anleitung zu Anzeige, HDMI IN, Audio und Fehlersuche

drivers/video/drm/rockchip_display.c
drivers/video/drm/Kconfig
drivers/video/drm/Makefile

configs/rk3568_defconfig //以rk3568平台为例

diff --git a/drivers/video/drm/rockchip_display.c b/drivers/video/drm/rockchip_display.c

index a1cb40a000e..041b8bdd84f 100644
--- a/drivers/video/drm/rockchip_display.c
+++ b/drivers/video/drm/rockchip_display.c
@@ -918,6 +918,23 @@ static int display_enable(struct display_state *state)
      if (state->enabled_at_spl == false)
           rockchip_connector_enable(state);

+#ifdef CONFIG_DRM_ROCKCHIP_RK628

+     /*
+     * trigger .probe helper of U_BOOT_DRIVER(rk628) in ./rk628/rk628.c
+     */
+     struct udevice * dev;
+     int phandle, ret;
+
+     phandle = ofnode_read_u32_default(state->node, "bridge", -1);
+     if (phandle < 0)
+          printf("%s failed to find bridge phandle\n",
ofnode_get_name(state->node));
+
+     ret = uclass_get_device_by_phandle_id(UCLASS_I2C_GENERIC, phandle, &dev);

+     if (ret && ret != -ENOENT)
+          printf("%s:%d failed to get rk628 device ret:%d\n", __func__,
__LINE__, ret);
+
+#endif
+
      if (crtc_state->soft_te)
           crtc_funcs->apply_soft_te(state);
diff --git a/drivers/video/drm/Kconfig b/drivers/video/drm/Kconfig
index ddc65818cba..c5073b9926b 100644
--- a/drivers/video/drm/Kconfig

+++ b/drivers/video/drm/Kconfig
@@ -191,6 +191,13 @@ config DRM_ROCKCHIP_RK618
       Choose this option to enable support for Rockchip RK618 display
       bridge chips driver. say Y to enable its driver.

+config DRM_ROCKCHIP_RK628
+     bool "Rockchip RK628 display bridge driver"
+     depends on DRM_ROCKCHIP
+     help
+      Choose this option to enable support for Rockchip RK628 display
+      bridge chips driver. say Y to enable its driver.
+
diff --git a/drivers/video/drm/Makefile b/drivers/video/drm/Makefile
index ea4219d9cf6..f11a8ff4885 100644

--- a/drivers/video/drm/Makefile
+++ b/drivers/video/drm/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_DRM_ROCKCHIP_RGB) += rockchip_rgb.o
 obj-$(CONFIG_DRM_ROCKCHIP_PANEL) += rockchip_panel.o
 obj-$(CONFIG_DRM_ROHM_BU18XL82) += rohm-bu18tl82.o rohm-bu18rl82.o
 obj-$(CONFIG_DRM_ROCKCHIP_RK618) += rk618.o rk618_lvds.o rk618_dsi.o
+obj-$(CONFIG_DRM_ROCKCHIP_RK628) += rk628/
 obj-$(CONFIG_DRM_ROCKCHIP_RK1000) += rk1000.o rk1000_tve.o
 obj-$(CONFIG_DRM_ROCKCHIP_SAMSUNG_MIPI_DCPHY) += samsung_mipi_dcphy.o
 obj-$(CONFIG_DRM_SII902X) += sii902x.o
diff --git a/configs/rk3568_defconfig b/configs/rk3568_defconfig
index acd1fb18169..94f1050eb4f 100644
--- a/configs/rk3568_defconfig

+++ b/configs/rk3568_defconfig
@@ -224,3 +224,4 @@ CONFIG_RK_AVB_LIBAVB_USER=y
 CONFIG_OPTEE_CLIENT=y
 CONFIG_OPTEE_V2=y
 CONFIG_OPTEE_ALWAYS_USE_SECURITY_PARTITION=y
+CONFIG_DRM_ROCKCHIP_RK628=y

 &route_rgb {
      status = "okay";

+
+     bridge = <&i2c2_rk628>;
 };

&route_hdmi {
      status = "okay";
+

+     bridge = <&i2c2_rk628>;
      force-bus-format = <MEDIA_BUS_FMT_RGB888_1X24>;
      force-output;
      force_timing{

misc: rk628: add support uboot logo

Type: Function

Redmine ID: #496880 #491750
Associated modifications: NULL
Test: NULL

Change-Id: I311e2c9682f835b377ea9082e1d3a88688167172
Signed-off-by: Guochun Huang <hero.huang@rock-chips.com>

diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 276c7c4fef15..8481b9613bc9 100644
--- a/drivers/misc/Kconfig

+++ b/drivers/misc/Kconfig
@@ -5,6 +5,8 @@

 menu "Misc devices"

+source "drivers/misc/rk628/Kconfig"
+
 config RK803
      tristate "RK803"
      default n
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index b296e760fd47..14642c54a2bc 100644

--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -3,6 +3,7 @@
 # Makefile for misc devices that really don't fit anywhere else.
 #

+obj-y                 += rk628/
 obj-$(CONFIG_RK803)   += rk803.o
 obj-y                 += rockchip/
 obj-$(CONFIG_LT7911D_FB_NOTIFIER) += lt7911d-fb-notifier.o
diff --git a/arch/arm64/configs/rockchip_defconfig b/arch/arm64/configs/rockchip_defconfig
index 28340b4bdfae..dbb7d9e55b62 100644

--- a/arch/arm64/configs/rockchip_defconfig
+++ b/arch/arm64/configs/rockchip_defconfig
@@ -294,6 +294,8 @@ CONFIG_BLK_DEV_LOOP_MIN_COUNT=16
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=8192
 CONFIG_BLK_DEV_NVME=y
+CONFIG_RK628_MISC=y
+CONFIG_RK628_MISC_HDMITX=y
 CONFIG_LT7911D_FB_NOTIFIER=y
 CONFIG_SRAM=y
 CONFIG_UID_SYS_STATS=y
@@ -557,7 +559,6 @@ CONFIG_ROCKCHIP_THERMAL=y

 CONFIG_WATCHDOG=y
 CONFIG_DW_WATCHDOG=y
 CONFIG_MFD_RK618=y
-CONFIG_MFD_RK628=y
 CONFIG_MFD_RK630_I2C=y
 CONFIG_MFD_RK806_I2C=y
 CONFIG_MFD_RK806_SPI=y
@@ -640,7 +641,6 @@ CONFIG_ROCKCHIP_LVDS=y
 CONFIG_ROCKCHIP_RGB=y
 CONFIG_ROCKCHIP_DW_HDCP2=y
 CONFIG_DRM_ROCKCHIP_RK618=y
-CONFIG_DRM_ROCKCHIP_RK628=y
CONFIG_DRM_PANEL_SIMPLE=y
CONFIG_DRM_PANEL_MAXIM_MAX96752F=y
CONFIG_DRM_PANEL_MAXIM_MAX96772=y

diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index f3273756c612..609bb5e3db07 100644
--- a/drivers/media/i2c/Kconfig

+++ b/drivers/media/i2c/Kconfig
@@ -414,6 +414,8 @@ config VIDEO_OTP_EEPROM
      help
       This driver supports OTP load from eeprom.

+source "drivers/media/i2c/rk628/Kconfig"
+
 config VIDEO_SAA7110
      tristate "Philips SAA7110 video decoder"
      depends on VIDEO_V4L2 && I2C
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 26edd6f7590e..d6f4128b19a5 100644

--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -141,6 +141,7 @@ obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o
 obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
 obj-$(CONFIG_VIDEO_TC358743) += tc358743.o
 obj-$(CONFIG_VIDEO_TC35874X) += tc35874x.o
+obj-$(CONFIG_VIDEO_RK628) += rk628/
 obj-$(CONFIG_VIDEO_AR0230) += ar0230.o
 obj-$(CONFIG_VIDEO_GC02M2) += gc02m2.o
 obj-$(CONFIG_VIDEO_GC08A3) += gc08a3.o
diff --git a/arch/arm64/configs/rockchip_defconfig b/arch/arm64/configs/rockchip_defconfig
index 95ad81b12a69..c66f67ecd0c2 100644

--- a/arch/arm64/configs/rockchip_defconfig
+++ b/arch/arm64/configs/rockchip_defconfig
@@ -567,6 +567,8 @@ CONFIG_VIDEO_ROCKCHIP_ISPP=y
 CONFIG_VIDEO_ROCKCHIP_HDMIRX=y
 CONFIG_VIDEO_LT6911UXC=y
 CONFIG_VIDEO_LT7911D=y
+CONFIG_VIDEO_RK628_CSI=y
+CONFIG_VIDEO_RK628_BT1120=y
 CONFIG_VIDEO_TC35874X=y
 CONFIG_VIDEO_GC0312=y
 CONFIG_VIDEO_GC2145=y

drivers/video/drm/rk628/
├── Makefile

├── panel.c
├── panel.h
├── rk628.c
├── rk628_combtxphy.c
├── rk628_combtxphy.h
├── rk628_cru.c
├── rk628_cru.h
├── rk628_dsi.c
├── rk628_dsi.h
├── rk628_gvi.c
├── rk628_gvi.h
├── rk628.h

├── rk628_hdmirx.c
├── rk628_hdmirx.h
├── rk628_hdmitx.h
├── rk628_lvds.c
├── rk628_lvds.h
├── rk628_post_process.c
├── rk628_post_process.h
├── rk628_rgb.c
└── rk628_rgb.h

drivers/misc/rk628/
├── Kconfig
├── Makefile

├── panel.c
├── panel.h
├── rk628.c
├── rk628_combrxphy.c
├── rk628_combrxphy.h
├── rk628_combtxphy.c
├── rk628_combtxphy.h
├── rk628_config.c

├── rk628_config.h
├── rk628_cru.c
├── rk628_cru.h
├── rk628_csi.c
├── rk628_csi.h
├── rk628_dsi.c
├── rk628_dsi.h
├── rk628_efuse.c
├── rk628_efuse.h
├── rk628_gpio.h
├── rk628_grf.h
├── rk628_gvi.c

├── rk628_gvi.h
├── rk628.h
├── rk628_hdmirx.c
├── rk628_hdmirx.h
├── rk628_hdmitx.c
├── rk628_hdmitx.h
├── rk628_lvds.c
├── rk628_lvds.h
├── rk628_pinctrl.c
├── rk628_pinctrl.h
├── rk628_post_process.c
├── rk628_post_process.h
├── rk628_rgb.c

├── rk628_rgb.h

&i2c2 {
   clock-frequency = <400000>;

   status = "okay";

   i2c2_rk628: rk628@50 {
      compatible = "rockchip,rk628";
      reg = <0x50>;
      interrupt-parent = <&gpio0>;
      interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
      enable-gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_reset>;
      status = "okay";
   };

};

&pinctrl {
   rk628 {
      rk628_reset: rk628-reset {
         rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
      };

   };
};

&i2c2_rk628 {
   /* soc_24M optional */
   pinctrl-names = "default";
   pinctrl-0 = <&rk628_reset &refclk_pins>;
   assigned-clocks = <&pmucru CLK_WIFI>;
   assigned-clock-rates = <24000000>;
   clocks = <&pmucru CLK_WIFI>;
   clock-names = "soc_24M";


   panel-backlight = <&backlight>;
   panel-power-supply = <&vcc3v3_lcd0_n>;
   panel-enable-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;

   panel-reset-delay-ms = <10>;
   panel-enable-delay-ms = <10>;
   panel-prepare-delay-ms = <60>;
   panel-unprepare-delay-ms = <10>;
   panel-disable-delay-ms = <60>;
   panel-init-delay-ms = <60>;

   rk628-rgb-in;
   rk628-dsi-out {

      dsi,eotp;
      dsi,video-mode;
      dsi,format = "rgb888";
      dsi,lanes = <4>;
      status = "okay";

      rk628-panel {
         panel-init-sequence = [
            05 78 01 11
            05 78 01 29
         ];


         panel-exit-sequence = [
            05 00 01 28
            05 00 01 10
         ];
      };
   };

   display-timings {
      src-timing {
         clock-frequency = <148500000>;
         hactive = <1920>;
         vactive = <1080>;
         hfront-porch = <88>;

         hsync-len = <44>;
         hback-porch = <148>;
         vfront-porch = <4>;
         vsync-len = <5>;
         vback-porch = <36>;
         hsync-active = <1>;

         vsync-active = <1>;
         de-active = <0>;
         pixelclk-active = <0>;
      };

      dst-timing {
         clock-frequency = <148500000>;
         hactive = <1920>;
         vactive = <1080>;
         hfront-porch = <88>;
         hsync-len = <44>;
         hback-porch = <148>;

         vfront-porch = <4>;
         vsync-len = <5>;
         vback-porch = <36>;
         hsync-active = <1>;
         vsync-active = <1>;
         de-active = <0>;
         pixelclk-active = <0>;
      };
   };
};

&i2c2 {
   clock-frequency = <400000>;

   status = "okay";

   i2c2_rk628: rk628@50 {
      compatible = "rockchip,rk628";
      reg = <0x50>;
      enable-gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_reset>;
      status = "okay";
   };
};


&pinctrl {
   rk628 {
      rk628_reset: rk628-reset {
         rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
      };
   };
};

&i2c2_rk628 {
   /* soc_24M optional */
   pinctrl-names = "default";

   pinctrl-0 = <&rk628_reset &refclk_pins>;
   assigned-clocks = <&pmucru CLK_WIFI>;
   assigned-clock-rates = <24000000>;
   clocks = <&pmucru CLK_WIFI>;
   clock-names = "soc_24M";
   ......
};

&pinctrl {
   ......
   refclk {

      /omit-if-no-ref/
      refclk_pins: refclk-pins {
         rockchip,pins =
           /* refclk_ou */
           <0 RK_PA0 1 &pcfg_pull_none>;
      };
   };
   ......
};

&i2c2_rk628 {
   ......

   rk628-rgb-in;
   rk628-dsi-out {
      ......
   };
   ......
};

&i2c2_rk628 {
   ......

   panel-backlight = <&backlight>;
   panel-power-supply = <&vcc3v3_lcd0_n>;
   panel-enable-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;

   panel-reset-delay-ms = <10>;
   panel-enable-delay-ms = <10>;
   panel-prepare-delay-ms = <60>;
   panel-unprepare-delay-ms = <10>;
   panel-disable-delay-ms = <60>;
   panel-init-delay-ms = <60>;
   ......
   display-timings {
      src-timing {

         clock-frequency = <148500000>;
         hactive = <1920>;
         vactive = <1080>;
         hfront-porch = <88>;
         hsync-len = <44>;
         hback-porch = <148>;
         vfront-porch = <4>;
         vsync-len = <5>;
         vback-porch = <36>;
         hsync-active = <1>;
         vsync-active = <1>;
         de-active = <0>;

         pixelclk-active = <0>;
      };

      dst-timing {
         clock-frequency = <148500000>;
         hactive = <1920>;
         vactive = <1080>;
         hfront-porch = <88>;
         hsync-len = <44>;
         hback-porch = <148>;
         vfront-porch = <4>;
         vsync-len = <5>;
         vback-porch = <36>;

         hsync-active = <1>;
         vsync-active = <1>;
         de-active = <0>;
         pixelclk-active = <0>;
      };
   };
   ......
};

src: hactive / dst: hactive = src: hblanking / dst: hblanking
src: vactive / dst: vactive = src: vblanking / dst: vblanking
hblanking = hfront-porch + hback-porch + hsync-len

vblanking = vfront-porch + vback-porch + vsync-len

src: clock-frequency / (htotal * vtotal) = dst: clock-frequency / (htotal *
vtotal)
htotal = hactive + hfront-porch + hback-porch + hsync-len

vtotal = vactive + vfront-porch + vback-porch + vsync-len

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2bt1120-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2dsi-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2dsi-dual-ddr4-v10.dts

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2gvi-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2lvds-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2lvds-dual-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2dsi-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2gvi-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2hdmi-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2lvds-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2lvds-dual-ddr4-v10.dts

# 1. 电压缩放 N=0(75%), 1/2(100%), 3(125%) (通常无需调节)
# echo 0x90004 $val > /d/rk628/2-0050/registers/combtxphy

# $val:
#   tx0[Bit1:0], tx1[Bit3:2], tx2[Bit5:4], tx3[Bit7:6], tx4[Bit9:8]
#   tx5[Bit17:16], tx6[Bit19:18], tx7[Bit21:20], tx8[Bit23:22], tx9[Bit25:24]
# 以 1(100%) 为例:
echo 0x90004 0x01550155 > /d/rk628/2-0050/registers/combtxphy

# 2. 电压调节 N=0~7
# echo 0x90008 $val > /d/rk628/2-0050/registers/combtxphy
# $val:
#   tx0[Bit2:0], tx1[Bit5:3], tx2[Bit8:6], tx3[Bit11:9], tx4[Bit14:12]
#   tx5[Bit18:16], tx6[Bit21:19], tx7[Bit24:22], tx8[Bit27:25], tx9[Bit30:28]
# 以 3 档为例:
echo 0x90008 0x36db36db > /d/rk628/2-0050/registers/combtxphy


# 3. 预加重调节 N=0~9
# echo 0x9000c $val > /d/rk628/2-0050/registers/combtxphy
# $val: tx0[Bit3:0], tx1[Bit7:4], tx2[Bit11:8], tx3[Bit15:12], tx4[Bit19:16]
# echo 0x90010 $val > /d/rk628/2-0050/registers/combtxphy
# $val: tx5[Bit3:0], tx6[Bit7:4], tx7[Bit11:8], tx8[Bit15:12], tx9[Bit19:16]
# 以 5 档为例:
echo 0x9000c 0x55555 > /d/rk628/2-0050/registers/combtxphy
echo 0x90010 0x55555 > /d/rk628/2-0050/registers/combtxphy

diff --git a/drivers/misc/rk628/rk628_combtxphy.c b/drivers/misc/rk628/rk628_combtxphy.c

index 3387d8bd73b9..70d7a5422a35 100644
--- a/drivers/misc/rk628/rk628_combtxphy.c
+++ b/drivers/misc/rk628/rk628_combtxphy.c
@@ -139,6 +139,14 @@ static void rk628_combtxphy_gvi_power_on(struct rk628
*rk628)
      usleep_range(100, 200);

      rk628_i2c_update_bits(rk628, COMBTXPHY_CON0,
                      SW_TX_IDLE_MASK, 0);
+
+     // amplitude scale
+     rk628_i2c_write(rk628, COMBTXPHY_CON1, 0x01550155);
+     // amplitude level
+     rk628_i2c_write(rk628, COMBTXPHY_CON2, 0x36db36db);
+     // emphasis level
+     rk628_i2c_write(rk628, COMBTXPHY_CON3, 0x00055555);
+     rk628_i2c_write(rk628, COMBTXPHY_CON4, 0x00055555);
 }


 void rk628_combtxphy_power_on(struct rk628 *rk628)

# 1. 驱动强度调节
# echo 0x70388 $val > /d/rk628/2-0050/registers/hdmi

# $val: clk_driver_strength[Bit7:4], data_driver_strength[Bit3:0]
#      范围（强度从低到高）：0x0  ~ 0xF
# 以 0x8 为例:
echo 0x70388 0x88 > /d/rk628/2-0050/registers/hdmi

# 2. 预加重调节
# echo 0x7038c $val > /d/rk628/2-0050/registers/hdmi
# $val: pre_emphasis_strength[Bit6:4]
#      范围（强度从低到高）：0x0  ~ 0x7
#     clk_pre_driver_strength[Bit3:2], data_pre_driver_strength[Bit1:0]
#      范围（强度从低到高）：0x0  ~ 0x3
# 以 pre_emphasis_strength = 0x3, clk/data_pre_driver_strength = 0x3 为例:

echo 0x7038c 0x3f > /d/rk628/2-0050/registers/hdmi

diff --git a/drivers/misc/rk628/rk628_hdmitx.c b/drivers/misc/rk628/rk628_hdmitx.c
index f28b78a6b525..2120cf504ebe 100644

--- a/drivers/misc/rk628/rk628_hdmitx.c
+++ b/drivers/misc/rk628/rk628_hdmitx.c
@@ -231,6 +231,7 @@ static void rk628_hdmi_sys_power(struct rk628_hdmi *hdmi,
bool enable)
 static struct rk628_hdmi_phy_config rk628_hdmi_phy_config[] = {
      /* pixelclk pre-emp vlev */
      { 74250000, 0x3f, 0x88 },
+     { 148500000, 0x3f, 0x88 },
      { 165000000, 0x3f, 0x88 },
      { ~0UL,  0x00, 0x00 }
 };

# echo 0xc000c $((val | 0xffff0000)) > /d/rk628/2-0050/registers/cru
# $val:
#   ssmod_spread[Bit12:8](Spread amplitude / 0.1%)

#   ssmod_divval[Bit7:4](Divider required to set the modulation frequency)
#   参数说明⻅下方描述
# 例 ssmod_spread = 3, ssmod_divval = 6 (推荐值):
echo 0xc000c 0xffff0360 > /d/rk628/2-0050/registers/cru

diff --git a/drivers/misc/rk628/rk628_combtxphy.c b/drivers/misc/rk628/rk628_combtxphy.c

index 3387d8bd73b9..70d7a5422a35 100644
--- a/drivers/misc/rk628/rk628_combtxphy.c
+++ b/drivers/misc/rk628/rk628_combtxphy.c
@@ -139,6 +139,9 @@ static void rk628_combtxphy_gvi_power_on(struct rk628 *rk628)
      usleep_range(100, 200);
      rk628_i2c_update_bits(rk628, COMBTXPHY_CON0,
                      SW_TX_IDLE_MASK, 0);
+
+     // ssmod
+     rk628_i2c_write(rk628, CRU_CPLL_CON3, 0xffff0360);
 }
void rk628_combtxphy_power_on(struct rk628 *rk628)

&i2c2_rk628 {
   ......

   rk628-rgb-in;
   ......
};

/ {
   panel@0 {
      compatible = "simple-panel";


      disp_timings3: display-timings {
         native-mode = <&rgb2dsi_timing>;
         rgb2dsi_timing: timing0 {
           clock-frequency = <148500000>;
           hactive = <1920>;
           vactive = <1080>;
           hfront-porch = <88>;
           hsync-len = <44>;
           hback-porch = <148>;
           vfront-porch = <4>;
           vsync-len = <5>;
           vback-porch = <36>;

           hsync-active = <1>;
           vsync-active = <1>;
           de-active = <0>;
           pixelclk-active = <0>;
         };
      };

      port {
         panel_in_rgb: endpoint {
           remote-endpoint = <&rgb_out_panel>;
         };
      };

   };
};
&route_rgb {
   status = "okay";


   /* for u-boot logo display */
   bridge = <&i2c2_rk628>;
};

&rgb_in_vp2 {
   status = "okay";
};

&rgb {
   status = "okay";


   ports {
      port@1 {
         reg = <1>;

         rgb_out_panel: endpoint {
           remote-endpoint = <&panel_in_rgb>;
         };
      };
   };c
};

&i2c2_rk628 {
   ......

   rk628-bt1120-in;
   // bt1120-dual-edge;
   // bt1120-yc-swap;
   // bt1120-uv-swap;
   ......
};

&i2c2_rk628 {
   ......
   rk628-hdmi-in;

   // src-mode-4k-yuv420;
   ......
};

#include <dt-bindings/display/media-bus-format.h>

&hdmi {

   status = "okay";
   force-bus-format = <MEDIA_BUS_FMT_RGB888_1X24>;
   force-output;
   force_timing{
      clock-frequency = <594000000>;
      hactive = <3840>;
      vactive = <2160>;
      hback-porch = <296>;
      hfront-porch = <176>;
      vback-porch = <72>;
      vfront-porch = <8>;
      hsync-len = <88>;
      vsync-len = <10>;

      hsync-active = <1>;
      vsync-active = <1>;
      de-active = <0>;
      pixelclk-active = <0>;
   };
};

&hdmi_in_vp0 {
   status = "okay";
};


&hdmi_in_vp1 {
   status = "disabled";
};

&route_hdmi {
   status = "okay";

   /* for u-boot logo display */
   bridge = <&i2c2_rk628>;
   force-bus-format = <MEDIA_BUS_FMT_RGB888_1X24>;
   force-output;
   force_timing{

      clock-frequency = <594000000>;
      hactive = <3840>;
      vactive = <2160>;
      hback-porch = <296>;
      hfront-porch = <176>;
      vback-porch = <72>;
      vfront-porch = <8>;
      hsync-len = <88>;
      vsync-len = <10>;
      hsync-active = <1>;
      vsync-active = <1>;
      de-active = <0>;
      pixelclk-active = <0>;

   };
};

&i2c2_rk628 {
   ......
   interrupt-parent = <&gpio0>;

   interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
   plugin-det-gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_LOW>;
   // hpd-output-inverted;
   rk628-hdmi-in;
   ......
};

rk628_dc: rk628-dc {
   compatible = "rockchip,dummy-codec";
   #sound-dai-cells = <0>;

};

&i2s0 {
   rockchip,capture-only;
   status = "okay";
};

/ {
   hdmiin-sound {
      compatible = "simple-audio-card";
      simple-audio-card,format = "i2s";
      simple-audio-card,name = "rockchip,hdmiin";

      simple-audio-card,bitclock-master = <&dailink0_master>;
      simple-audio-card,frame-master = <&dailink0_master>;
      status = "okay";
      simple-audio-card,cpu {
         sound-dai = <&i2s0>;
      };
      dailink0_master: simple-audio-card,codec {
         sound-dai = <&rk628_dc>;
      };
   };
};

diff --git a/sound/soc/rockchip/rockchip_i2s.c b/sound/soc/rockchip/rockchip_i2s.c

index 9bc29fdd13c5..230c350c6765
--- a/sound/soc/rockchip/rockchip_i2s.c
+++ b/sound/soc/rockchip/rockchip_i2s.c
@@ -468,6 +468,9 @@ static int rockchip_i2s_trigger(struct snd_pcm_substream
*substream,
           ret = -EINVAL;
           break;
      }
+     if(substream->stream == SNDRV_PCM_STREAM_CAPTURE) {
+          substream->wait_time = msecs_to_jiffies(100);
+     }

      return ret;

 }
diff --git a/sound/soc/rockchip/rockchip_i2s_tdm.c b/sound/soc/rockchip/rockchip_i2s_tdm.c
index b0c4ce01e2be..0602df42c309
--- a/sound/soc/rockchip/rockchip_i2s_tdm.c
+++ b/sound/soc/rockchip/rockchip_i2s_tdm.c
@@ -1776,6 +1776,9 @@ static int rockchip_i2s_tdm_trigger(struct

snd_pcm_substream *substream,
           ret = -EINVAL;
           break;
      }
+     if(substream->stream == SNDRV_PCM_STREAM_CAPTURE) {
+          substream->wait_time = msecs_to_jiffies(100);
+     }

      return ret;
 }

&i2c2_rk628 {
   ......
   rk628-rgb-out;

   ......
};

&i2c2_rk628 {
   ......
   rk628-bt1120-out;

   // bt1120-dual-edge;
   ......
};

&i2c2_rk628 {
   ......
   rk628-dsi-out {

      // rockchip,lane-mbps = <1100>;
      // rockchip,dual-channel;
      dsi,eotp;
      dsi,video-mode;
      // dsi,clk-non-continuous;
      dsi,format = "rgb888";
      dsi,lanes = <4>;
      status = "okay";

      rk628-panel {
         panel-init-sequence = [
           ......

           05 78 01 11
           05 78 01 29
         ];

         panel-exit-sequence = [
           05 00 01 28
           05 00 01 10
         ];
      };
   };
   ......
};

&i2c2_rk628 {
   ......
   rk628-lvds {

      bus-format = <MEDIA_BUS_FMT_RGB888_1X7X4_SPWG>;
      link-type = "single_link";
      status = "okay";
   };
   ......
};

&i2c2_rk628 {
   ......
   rk628-gvi-out {

      bus-format = "rgb888";
      gvi,lanes = <8>;
      // rockchip,division-mode;
      // rockchip, gvi-frm-rst;
      status = "okay";
   };
   ......
};

# echo 0x80004 $val > /d/rk628/2-0050/registers/combtxphy
# $val(combtx_lane_n):

#   lane0[Bit2:0], lane1[Bit6:4], lane2[Bit10:8], lane3[Bit14:12]
#   lane4[Bit18:16], lane5[Bit22:20], lane6[Bit26:24], lane7[Bit30:28]
# 显示异常时可以优先考虑如下常用   val 值：
# 0x01234567 0x76543210 0x10325476 0x67452301 0x45670123 0x32107654 0x54761023
0x23016745
# 例：
echo 0x80004 0x01234567 > /d/rk628/2-0050/registers/combtxphy

diff --git a/drivers/misc/rk628/rk628_gvi.c b/drivers/misc/rk628/rk628_gvi.c
index fb41c2143bb5..ef47e58ad377 100644
--- a/drivers/misc/rk628/rk628_gvi.c

+++ b/drivers/misc/rk628/rk628_gvi.c
@@ -150,6 +150,8 @@ static void rk628_gvi_pre_enable(struct rk628 *rk628, struct
rk628_gvi *gvi)

      rk628_i2c_update_bits(rk628, GVI_SYS_CTRL1, SYS_CTRL1_COLOR_DEPTH_MASK,
                      SYS_CTRL1_COLOR_DEPTH(gvi->color_depth));
+
+     rk628_i2c_write(rk628, GVI_SYS_CTRL3, 0x01234567);
 }

 static void rk628_gvi_enable_color_bar(struct rk628 *rk628,

&i2c2_rk628 {
   pinctrl-names = "default";

   pinctrl-0 = <&rk628_reset &refclk_pins>;
   assigned-clocks = <&pmucru CLK_WIFI>;
   assigned-clock-rates = <24000000>;
   clock-names = "soc_24M";
   clocks = <&pmucru CLK_WIFI>;

   rk628-rgb-in;
   rk628-hdmi-out;
   // mode-sync-pol = <0>;
   status = "okay";

   port {

      rgb_in_hdmi: endpoint {
         remote-endpoint = <&rgb_out_hdmi>;
      };
   };
};
&route_rgb {
   status = "disabled";

};

&rgb_in_vp2 {
   status = "okay";
};

&rgb {
   status = "okay";

   ports {
      port@1 {
         reg = <1>;


         rgb_out_hdmi: endpoint {
           remote-endpoint = <&rgb_in_hdmi>;
         };
      };
   };
};

&i2s0 {
   rockchip,playback-only;

   status = "oaky";
};

/ {
   rk628_sound: rk628-sound {
      compatible = "simple-audio-card";
      simple-audio-card,format = "i2s";
      simple-audio-card,mclk-fs = <128>;
      simple-audio-card,name = "rockchip,hdmi-rk628";
      status = "oaky";
      simple-audio-card,cpu {
         sound-dai = <&i2s0>;
      };
      simple-audio-card,codec {
         sound-dai = <&i2c2_rk628>;
      };

   };
}

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-ddr4-v10.dtsi
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2dsi-ddr4-v10.dts

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-ddr4-v10.dtsi
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2lvds-ddr4-v10.dts
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2lvds-dual-ddr4-v10.dts

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-ddr4-v10.dtsi
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2gvi-ddr4-v10.dts

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-ddr4-v10.dtsi
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2hdmi-ddr4-v10.dts

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-ddr4-v10.dtsi
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2dsi-ddr4-v10.dts

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2dsi-dual-ddr4-v10.dts

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-ddr4-v10.dtsi
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2lvds-ddr4-v10.dts

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2lvds-dual-ddr4-v10.dts

arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-ddr4-v10.dtsi
arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2gvi-ddr4-v10.dts

rk3568_t:/ # ls /sys/kernel/debug/regmap/
0-001c        2-0050-dsi1 2-0050-hdmirx 4-0050-gpio0
0-0020        2-0050-efuse 4-0050-adapter 4-0050-gpio1

0-0020-rk817-codec 2-0050-gpio0 4-0050-combrxphy 4-0050-gpio2
2-0050-adapter 2-0050-gpio1 4-0050-combtxphy 4-0050-gpio3
2-0050-combrxphy 2-0050-gpio2 4-0050-cru 4-0050-grf
2-0050-combtxphy 2-0050-gpio3 4-0050-csi 4-0050-gvi
2-0050-cru    2-0050-grf 4-0050-dsi0  4-0050-hdmi
2-0050-csi    2-0050-gvi 4-0050-dsi1  4-0050-hdmirx
2-0050-dsi0   2-0050-hdmi 4-0050-efuse ......

rk3568_t:/ # ls /sys/kernel/debug/rk628/2-0050/registers/
adapter combrxphy combtxphy cru csi dsi0 dsi1 efuse gpio0 gpio1 gpio2
gpio3 grf gvi hdmi hdmirx

rk3568_t:/ # cat /sys/kernel/debug/regmap/2-0050-grf/registers
000: 06000088
004: ffffffff

008: 00000000
00c: 00000000
010: 00000001
014: 00000000
018: 00050000
01c: 002c0898
020: 00c00840
......

rk3568_t:/ # cat /sys/kernel/debug/regmap/2-0050-grf/registers | grep 200:
200: 20230321

rk3568_t:/ # cat /sys/kernel/debug/rk628/2-0050/registers/grf
rk628_grf:


0x0000: 06000298 ffffffff 00000000 00000001
0x0010: 00000001 00000000 000404b6 002804ba
0x0020: 0046047e 000a079e 00140794 0046047e
0x0030: 00140794 00000004 00000000 00000000
0x0040: 04380004 80000000 00000000 00000000
0x0050: 80000000 00000000 10000000 00000000
0x0060: 000002ea 01f0ea00 00000000 01f00000
0x0070: 0000155c 00005602 00000000 00000000
0x0080: 00006000 00000000 00000000 00000000
......

rk3568_t:/ # cat /sys/kernel/debug/rk628/2-0050/registers/grf | grep 0200:

0x0200: 20230321 00000000 00000000 00000000

rk3568_t:/ # echo 0x010 0x02000200 > /sys/kernel/debug/regmap/2-0050-
grf/registers

rk3568_t:/ # echo 0x010 0x02000200 > /sys/kernel/debug/rk628/2-0050/registers/grf

# Enable horizontal color bar
rk3568_t:/ # echo 1 > /sys/kernel/debug/rk628/2-0050/scaler_color_bar


# Enable vertical color bar
rk3568_t:/ # echo 2 > /sys/kernel/debug/rk628/2-0050/scaler_color_bar

# Disable color bar
rk3568_t:/ # echo 0 > /sys/kernel/debug/rk628/2-0050/scaler_color_bar

# Enable normal color bar
rk3568_t:/ # echo 1 > /sys/kernel/debug/rk628/2-0050/hdmitx_color_bar


# Enable special color bar
rk3568_t:/ # echo 2 > /sys/kernel/debug/rk628/2-0050/hdmitx_color_bar

# Enable black color bar
rk3568_t:/ # echo 3 > /sys/kernel/debug/rk628/2-0050/hdmitx_color_bar

# Disable color bar
rk3568_t:/ # echo 0 > /sys/kernel/debug/rk628/2-0050/hdmitx_color_bar

# Enable dsi color bar
rk3568_t:/ # echo 1 > /sys/kernel/debug/rk628/2-0050/dsi_color_bar


# Disable dsi color bar
rk3568_t:/ # echo 0 > /sys/kernel/debug/rk628/2-0050/dsi_color_bar

# Enable color bar
rk3568_t:/ # echo 1 > /sys/kernel/debug/rk628/2-0050/gvi_color_bar


# Disable color bar
rk3568_t:/ # echo 0 > /sys/kernel/debug/rk628/2-0050/gvi_color_bar

rk3568_t:/ # cat /sys/kernel/debug/rk628/2-0050/rgb_resolution
1080x1920 pclk:131967000

rk3568_t:/ # dmesg | grep rk628
[  0.294331] rk628 2-0050: the driver version is 0.1.0 of RK628-F/B/G

[  0.294426] rk628 2-0050: failed to request enable GPIO: -16

[  0.960609] rk628 1-0050: failed to access register: -6

--- a/arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2dsi-ddr4-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2dsi-ddr4-v10.dts
@@ -347,8 +347,8 @@ src-timing {

                       vfront-porch = <15>;
                       hsync-len = <2>;
                       vsync-len = <2>;
-                      hsync-active = <0>;
-                      vsync-active = <0>;
+                      hsync-active = <1>;
+                      vsync-active = <1>;
                       de-active = <0>;
                       pixelclk-active = <0>;

--- a/arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2dsi-ddr4-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2dsi-ddr4-v10.dts
@@ -338,7 +338,7 @@ rk628-panel {


           display-timings {
                 src-timing {
-                      clock-frequency = <132000000>;
+                      clock-frequency = <148500000>;
                       hactive = <1080>;
                       vactive = <1920>;
                       hback-porch = <30>;
@@ -354,7 +354,7 @@ src-timing {
                 };

                 dst-timing {

-                      clock-frequency = <132000000>;
+                      clock-frequency = <148500000>;
                       hactive = <1080>;
                       vactive = <1920>;
                       hback-porch = <30>;

--- a/arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2dsi-ddr4-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-rgb2dsi-ddr4-v10.dts
@@ -57,6 +57,7 @@ &i2c2_rk628 {


           rk628-rgb-in;
           rk628-dsi-out {
+                rockchip,lane-mbps = <1000>;
                 //rockchip,dual-channel;
                 dsi,eotp;
                 dsi,video-mode;

--- a/arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2dsi-ddr4-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb-rk628-hdmi2dsi-ddr4-v10.dts
@@ -314,7 +314,7 @@ src-timing {

                 hfront-porch = <60>;
                 vback-porch = <10>;
                 vfront-porch = <10>;
-                hsync-len = <20>;
+                hsync-len = <40>;
                 vsync-len = <10>;
                 hsync-active = <1>;
                 vsync-active = <1>;

#include "rk628_pinctrl.h"
#include "rk628_gpio.h"


rk628_misc_gpio_direction_output(rk628, GPIO0_A6, 1);

rk628_misc_pinctrl_set_mux(rk628, GPIO0_A6, I2SM0D2);

主要改进点

解决了不同图像格式输入，格式转换下采样引入的色偏问题
增加一路  MIPI-CSI，双 MIPI-CSI 支持 4K60 输出

drivers/media/i2c/rk628
├── Makefile

├── rk628_bt1120_v4l2.c
├── rk628.c
├── rk628_combrxphy.c
├── rk628_combrxphy.h
├── rk628_combtxphy.c
├── rk628_combtxphy.h
├── rk628_cru.c
├── rk628_cru.h
├── rk628_csi.c
├── rk628_csi.h
├── rk628_csi_v4l2.c
├── rk628_dsi.c

├── rk628_dsi.h
├── rk628_gpio.h
├── rk628_grf.h
├── rk628.h
├── rk628_hdmirx.c
├── rk628_hdmirx.h
├── rk628_mipi_dphy.c
├── rk628_mipi_dphy.h
├── rk628_pinctrl.c
├── rk628_pinctrl.h
├── rk628_post_process.c
├── rk628_post_process.h

└── rk628_v4l2_controls.h

drivers/media/i2c/rk628
├── Makefile

├── rk628_bt1120_v4l2.c
├── rk628.c
├── rk628_combrxphy.c
├── rk628_combrxphy.h
├── rk628_combtxphy.c
├── rk628_combtxphy.h
├── rk628_cru.c
├── rk628_cru.h
├── rk628_csi.c
├── rk628_csi.h
├── rk628_csi_v4l2.c
├── rk628_dsi.c
├── rk628_dsi.h

├── rk628.h
├── rk628_hdmirx.c
├── rk628_hdmirx.h
├── rk628_mipi_dphy.c
├── rk628_mipi_dphy.h
├── rk628_post_process.c
└── rk628_post_process.h

&i2c5 {
   status = "okay";


   rk628_csi: rk628_csi@50 {
      reg = <0x50>;
      compatible = "rockchip,rk628-csi-v4l2";
      status = "okay";
      power-domains = <&power RK3588_PD_VI>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_pin>;
      interrupt-parent = <&gpio2>;
      interrupts = <RK_PC4 IRQ_TYPE_LEVEL_HIGH>;
      enable-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
      plugin-det-gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_LOW>;

      continues-clk = <1>;

      rockchip,camera-module-index = <0>;
      rockchip,camera-module-facing = "back";
      rockchip,camera-module-name = "HDMI-MIPI";
      rockchip,camera-module-lens-name = "RK628-CSI";

      multi-dev-info {
         dev-idx-l = <0>;
         dev-idx-r = <1>;
         combine-idx = <0>;
         pixel-offset = <0>;

         dev-num = <2>;
      };

      port {
         hdmiin_out0: endpoint {
           remote-endpoint = <&hdmi_mipi0_in>;
           data-lanes = <1 2 3 4>;
         };
      };
   };
};

&rk628_csi {
   status = "okay";
   /*

   * If the hpd output level is inverted on the circuit,
   * the following configuration needs to be enabled.
   */
   /* hpd-output-inverted; */
   plugin-det-gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
   power-gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
   rockchip,camera-module-index = <0>;
   rockchip,camera-module-facing = "back";
   rockchip,camera-module-name = "RK628-CSI";

   rockchip,camera-module-lens-name = "NC";

   port {
      hdmiin_out0: endpoint {
         remote-endpoint = <&mipi_in>;
         data-lanes = <1 2 3 4>;
      };
   };
};

&mipi_phy_rx0 {
   status = "okay";


   ports {
      #address-cells = <1>;
      #size-cells = <0>;

      port@0 {
         reg = <0>;
         #address-cells = <1>;
         #size-cells = <0>;

         mipi_in: endpoint@1 {
            reg = <1>;
            remote-endpoint = <&hdmiin_out0>;

            data-lanes = <1 2 3 4>;
         };
      };

      port@1 {
         reg = <1>;
         #address-cells = <1>;
         #size-cells = <0>;

         dphy_rx_out: endpoint@0 {
            reg = <0>;
            remote-endpoint = <&isp_mipi_in>;

         };
      };
   };
};

&rkisp1 {
   status = "okay";
   port {
      #address-cells = <1>;
      #size-cells = <0>;

      isp_mipi_in: endpoint@0 {
         reg = <0>;

         remote-endpoint = <&dphy_rx_out>;
      };
   };
};

&isp_mmu {

   status = "okay";
};

&i2c2 {
   status = "okay";

   pinctrl-names = "default";
   pinctrl-0 = <&i2c2m1_xfer>;

   rk628_csi: rk628_csi@32 {
      compatible = "rockchip,rk628-csi-v4l2";
      reg = <0x50>;
      interrupt-parent = <&gpio4>;
      interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_irq>;
      reset-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_LOW>;
      plugin-det-gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
      rockchip,camera-module-index = <0>;

      rockchip,camera-module-facing = "back";
      rockchip,camera-module-name = "RK628-CSI";
      rockchip,camera-module-lens-name = "NC";
      port {
         rk628_out: endpoint {
           remote-endpoint = <&mipi_in>;
           data-lanes = <1 2 3 4>;
         };
      };
   };
};


&csi2_dphy_hw {
   status = "okay";
};

&csi2_dphy0 {
   status = "okay";

   ports {
      #address-cells = <1>;
      #size-cells = <0>;
      port@0 {
         reg = <0>;
         #address-cells = <1>;

         #size-cells = <0>;

         mipi_in: endpoint@0 {
           reg = <0>;
           remote-endpoint = <&rk628_out>;
           data-lanes = <1 2 3 4>;
         };
      };
      port@1 {
         reg = <1>;

         #address-cells = <1>;
         #size-cells = <0>;

         csidphy0_out: endpoint@0 {
           reg = <0>;
           remote-endpoint = <&isp0_in>;
         };
      };
   };
};

&rkisp {

   status = "okay";
};

&rkisp_mmu {
   status = "okay";
};

&rkisp_vir0 {
   status = "okay";

   port {
      #address-cells = <1>;
      #size-cells = <0>;


      isp0_in: endpoint@0 {
         reg = <0>;
         remote-endpoint = <&csidphy0_out>;
      };
   };
};

&i2c2 {
   status = "okay";
   pinctrl-names = "default";

   pinctrl-0 = <&i2c2m1_xfer>;

   rk628_csi: rk628_csi@32 {
      compatible = "rockchip,rk628-csi-v4l2";
      reg = <0x50>;
      //clocks = <&ext_cam_clk>;
      //clock-names = "xvclk";

      interrupt-parent = <&gpio4>;
      interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_irq>;

      //power-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_LOW>;
      plugin-det-gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
      rockchip,camera-module-index = <0>;
      rockchip,camera-module-facing = "back";

      rockchip,camera-module-name = "RK628-CSI";
      rockchip,camera-module-lens-name = "NC";
      port {
         rk628_out: endpoint {
            remote-endpoint = <&mipi_in>;
            data-lanes = <1 2 3 4>;
         };
      };
   };
};

&csi2_dphy_hw {

   status = "okay";
};

&csi2_dphy0 {
   status = "okay";

   ports {
      #address-cells = <1>;
      #size-cells = <0>;
      port@0 {
         reg = <0>;
         #address-cells = <1>;
         #size-cells = <0>;


         mipi_in: endpoint@0 {
            reg = <0>;
            remote-endpoint = <&rk628_out>;
            data-lanes = <1 2 3 4>;
         };
      };
      port@1 {
         reg = <1>;
         #address-cells = <1>;
         #size-cells = <0>;


         csidphy0_out: endpoint@0 {
            reg = <0>;
            remote-endpoint = <&mipi_csi2_input>;
            data-lanes = <1 2 3 4>;
         };
      };
   };
};

&mipi_csi2 {
   status = "okay";

   ports {

      #address-cells = <1>;
      #size-cells = <0>;
      port@0 {
         reg = <0>;
         #address-cells = <1>;

         #size-cells = <0>;

         mipi_csi2_input: endpoint@1 {
           reg = <1>;
           remote-endpoint = <&csidphy0_out>;
           data-lanes = <1 2 3 4>;
         };
      };

      port@1 {
         reg = <1>;
         #address-cells = <1>;

         #size-cells = <0>;

         mipi_csi2_output: endpoint@0 {
           reg = <0>;
           remote-endpoint = <&cif_mipi_in>;
           data-lanes = <1 2 3 4>;
         };
      };
   };
};

&rkcif {
   status = "okay";

};

&rkcif_mipi_lvds {
   status = "okay";

   port {
      cif_mipi_in: endpoint {
         remote-endpoint = <&mipi_csi2_output>;
         data-lanes = <1 2 3 4>;
      };
   };
};


&rkcif_mmu {
   status = "okay";
};

&csi2_dphy0 {
   status = "okay";
   ports {
      #address-cells = <1>;

      #size-cells = <0>;
      port@0 {
         reg = <0>;
         #address-cells = <1>;
         #size-cells = <0>;

         hdmi_mipi2_in: endpoint@1 {
            reg = <1>;
            remote-endpoint = <&hdmiin_out1>;
            data-lanes = <1 2 3 4>;
         };
      };

      port@1 {
         reg = <1>;
         #address-cells = <1>;
         #size-cells = <0>;

         csidphy0_out: endpoint@0 {
            reg = <0>;
            remote-endpoint = <&mipi2_csi2_input>;
         };
      };
   };
};


&csi2_dphy0_hw {
   status = "okay";
};

&csi2_dphy1_hw {
   status = "okay";
};

&i2c3 {
   status = "okay";
   clock-frequency = <400000>;


   rk628_csi: rk628_csi@50 {
      reg = <0x50>;
      compatible = "rockchip,rk628-csi-v4l2";
      status = "okay";
      power-domains = <&power RK3588_PD_VI>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_pin>;
      interrupt-parent = <&gpio1>;
      interrupts = <RK_PB2 IRQ_TYPE_LEVEL_HIGH>;
      enable-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio1 RK_PB1 GPIO_ACTIVE_HIGH>;
      plugin-det-gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_LOW>;
      continues-clk = <1>;


      rockchip,camera-module-index = <0>;
      rockchip,camera-module-facing = "back";
      rockchip,camera-module-name = "HDMI-MIPI2";
      rockchip,camera-module-lens-name = "RK628-CSI";


      multi-dev-info {
         dev-idx-l = <2>;
         dev-idx-r = <4>;
         combine-idx = <2>;
         pixel-offset = <0>;
         dev-num = <2>;
      };

      port {
         hdmiin_out1: endpoint {
            remote-endpoint = <&hdmi_mipi2_in>;
            data-lanes = <1 2 3 4>;

         };
      };
   };
};

&mipi_dcphy0 {
   status = "okay";
};

&mipi_dcphy1 {
   status = "okay";
};


&mipi2_csi2 {
   status = "okay";

   ports {
      #address-cells = <1>;
      #size-cells = <0>;

      port@0 {
         reg = <0>;
         #address-cells = <1>;
         #size-cells = <0>;


         mipi2_csi2_input: endpoint@1 {
            reg = <1>;
            remote-endpoint = <&csidphy0_out>;
         };
      };

      port@1 {
         reg = <1>;
         #address-cells = <1>;
         #size-cells = <0>;

         mipi2_csi2_output: endpoint@0 {
            reg = <0>;

            remote-endpoint = <&cif_mipi_in2>;
         };
      };
   };
};


&rkcif {
   status = "okay";
};

&rkcif_mipi_lvds2 {
   status = "okay";

   port {
      cif_mipi_in2: endpoint {
         remote-endpoint = <&mipi2_csi2_output>;
      };
   };

};

&rkcif_mmu {
   status = "okay";
};

&i2c2 {
   status = "okay";
   pinctrl-names = "default";

   pinctrl-0 = <&i2c2m1_xfer>;

   rk628_csi: rk628_csi@32 {
      compatible = "rockchip,rk628-dsi-v4l2";
      reg = <0x50>;

      interrupt-parent = <&gpio4>;
      interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_irq>;
      //power-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_LOW>;

      plugin-det-gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
      rockchip,camera-module-index = <0>;
      rockchip,camera-module-facing = "back";
      rockchip,camera-module-name = "RK628-CSI";
      rockchip,camera-module-lens-name = "NC";
      port {
         rk628_out: endpoint {
            remote-endpoint = <&hdmi2mipi_in>;
            data-lanes = <1 2 3 4>;
         };
      };
   };

};

&mipi_csi2 {
   status = "okay";

   ports {
      #address-cells = <1>;
      #size-cells = <0>;

      port@0 {
         reg = <0>;
         #address-cells = <1>;
         #size-cells = <0>;


         mipi_csi2_input: endpoint@1 {
            reg = <1>;
            remote-endpoint = <&csidphy_out>;
            data-lanes = <1 2 3 4>;
         };
      };

      port@1 {
         reg = <1>;
         #address-cells = <1>;
         #size-cells = <0>;


         mipi_csi2_output: endpoint@0 {
            reg = <0>;
            remote-endpoint = <&cif_mipi_in>;
            data-lanes = <1 2 3 4>;
         };
      };
   };
};

&rkcif {
   status = "okay";
};


&rkcif_mipi_lvds {
   status = "okay";
   port {
      cif_mipi_in: endpoint {

         remote-endpoint = <&mipi_csi2_output>;
         data-lanes = <1 2 3 4>;
      };
   };
};

&rkcif_mmu {
   status = "okay";
};

&csi2_dphy_hw {
   status = "okay";

};

&csi2_dphy0 {
   status = "okay";

   ports {
      #address-cells = <1>;
      #size-cells = <0>;
      port@0 {
         reg = <0>;
         #address-cells = <1>;
         #size-cells = <0>;


         hdmi2mipi_in: endpoint@0 {
           reg = <1>;
           remote-endpoint = <&rk628_out>;
           data-lanes = <1 2 3 4>;
         };
      };
      port@1 {
         reg = <1>;
         #address-cells = <1>;
         #size-cells = <0>;

         csidphy_out: endpoint@0 {

           reg = <0>;
           remote-endpoint = <&mipi_csi2_input>;
         };
      };
   };
};

From e925e385a41a857e8e50020b5df9a2d41b166d83 Mon Sep 17 00:00:00 2001
From: Zefa Chen <zefa.chen@rock-chips.com>
Date: Thu, 02 Sep 2021 15:07:13 +0800

Subject: [PATCH] media: rockchip: cif fix errors in rgb24 data format
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
Change-Id: I0766997860f06dc25e604c2ea8425049a987fdc5

---

diff --git a/drivers/media/platform/rockchip/cif/capture.c b/drivers/media/platform/rockchip/cif/capture.c
index 6c0aa7d..36bd2c9 100644
--- a/drivers/media/platform/rockchip/cif/capture.c
+++ b/drivers/media/platform/rockchip/cif/capture.c
@@ -1785,13 +1785,11 @@
     * needs aligned with :ALIGN(bits_per_pixel * width * 2, 8), to optimize
reading and
     * writing of ddr, aliged with 256
     */

-   if (fmt->fmt_type == CIF_FMT_TYPE_RAW && stream->is_compact) {
+   if (fmt->fmt_type == CIF_FMT_TYPE_RAW && stream->is_compact &&
+      fmt->csi_fmt_val != CSI_WRDDR_TYPE_RGB888) {
       channel->virtual_width = ALIGN(channel->width * fmt->raw_bpp / 8, 256);
    } else {
-      if (fmt->fmt_type == CIF_FMT_TYPE_RAW && fmt->csi_fmt_val !=
CSI_WRDDR_TYPE_RAW8)
-         channel->virtual_width = ALIGN(channel->width * 2, 8);
-      else
-         channel->virtual_width = ALIGN(channel->width * fmt->bpp[0] / 8, 8);
+      channel->virtual_width = ALIGN(channel->width * fmt->bpp[0] / 8, 8);
    }


    if (channel->fmt_val == CSI_WRDDR_TYPE_RGB888)
@@ -3240,7 +3238,8 @@

       if (fmt->fmt_type == CIF_FMT_TYPE_RAW && stream->is_compact &&
          (dev->active_sensor->mbus.type == V4L2_MBUS_CSI2 ||
-         dev->active_sensor->mbus.type == V4L2_MBUS_CCP2)) {
+         dev->active_sensor->mbus.type == V4L2_MBUS_CCP2) &&
+         fmt->csi_fmt_val != CSI_WRDDR_TYPE_RGB888) {
          bpl = ALIGN(width * fmt->raw_bpp / 8, 256);
       } else {
          bpp = rkcif_align_bits_per_pixel(stream, fmt, i);
@@ -4659,13 +4658,11 @@

     * needs aligned with :ALIGN(bits_per_pixel * width * 2, 8), to optimize
reading and
     * writing of ddr, aliged with 256
     */
-   if (fmt->fmt_type == CIF_FMT_TYPE_RAW && stream->is_compact) {
+   if (fmt->fmt_type == CIF_FMT_TYPE_RAW && stream->is_compact &&
+      fmt->csi_fmt_val != CSI_WRDDR_TYPE_RGB888) {
       *crop_vwidth = ALIGN(raw_width * fmt->raw_bpp / 8, 256);
    } else {
-      if (fmt->fmt_type == CIF_FMT_TYPE_RAW)
-         *crop_vwidth = ALIGN(raw_width * 2, 8);
-      else
-         *crop_vwidth = ALIGN(raw_width * fmt->bpp[0] / 8, 8);

+      *crop_vwidth = ALIGN(raw_width * fmt->bpp[0] / 8, 8);
    }
if (channel->fmt_val == CSI_WRDDR_TYPE_RGB888)

diff --git a/drivers/media/platform/rockchip/cif/capture.c b/drivers/media/platform/rockchip/cif/capture.c

index 36bd2c99c707..fc4181daed2c 100644
--- a/drivers/media/platform/rockchip/cif/capture.c
+++ b/drivers/media/platform/rockchip/cif/capture.c
@@ -1753,7 +1753,7 @@ static int rkcif_csi_channel_init(struct rkcif_stream
*stream,

      channel->fmt_val = stream->cif_fmt_out->csi_fmt_val;

-     channel->cmd_mode_en = 0; /* default use DSI Video Mode */
+     channel->cmd_mode_en = 1; /* default use DSI Video Mode */

      if (stream->crop_enable) {
           channel->crop_en = 1;

diff --git a/psl/rkisp2/RKISP2GraphConfig.cpp b/psl/rkisp2/RKISP2GraphConfig.cpp
index 2a5fa5a..3d2409c 100755
--- a/psl/rkisp2/RKISP2GraphConfig.cpp

+++ b/psl/rkisp2/RKISP2GraphConfig.cpp
@@ -76,6 +76,7 @@ const string MEDIACTL_POSTVIEWNAME = "postview";

 const string MEDIACTL_STATNAME = "rkisp1-statistics";
 const string MEDIACTL_VIDEONAME_CIF = "stream_cif_dvp_id0";
+const string MEDIACTL_VIDEONAME_CIF_MIPI_ID0 = "stream_cif_mipi_id0";

 RKISP2GraphConfig::RKISP2GraphConfig() :
      mManager(nullptr),
@@ -2620,6 +2621,13 @@ status_t RKISP2GraphConfig::getImguMediaCtlConfig(int32_t
cameraId,
            addLinkParams("rkisp-isp-subdev", 2, "rkisp_mainpath", 0, 1,

MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
            addLinkParams("rkisp-isp-subdev", 2, "rkisp_selfpath", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
         }
+     } else if(mipName2.find("mipi") != std::string::npos) {
+        addLinkParams(mipName, mipSrcPad, mipName2, csiSinkPad, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
+        addLinkParams(mipName2, 1, "stream_cif_mipi_id0", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
+        addLinkParams(mipName2, 2, "stream_cif_mipi_id1", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
+        addLinkParams(mipName2, 3, "stream_cif_mipi_id2", 0, 1,

MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
+        addLinkParams(mipName2, 4, "stream_cif_mipi_id3", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
+        mSensorLinkedToCIF = true;
      } else {
         addLinkParams(mipName, mipSrcPad, csiName, csiSinkPad, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
         addLinkParams(csiName, csiSrcPad, IspName, ispSinkPad, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
@@ -2628,6 +2636,12 @@ status_t RKISP2GraphConfig::getImguMediaCtlConfig(int32_t
cameraId,
         addLinkParams(csiName, 5, "rkisp_rawwr3", 0, 1,

MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
      }
   }
+  if(mSensorLinkedToCIF){
+     addImguVideoNode(IMGU_NODE_VIDEO, MEDIACTL_VIDEONAME_CIF_MIPI_ID0,
mediaCtlConfig);
+     addFormatParams(MEDIACTL_VIDEONAME_CIF_MIPI_ID0, mCurSensorFormat.width,
mCurSensorFormat.height,
+           0, V4L2_PIX_FMT_NV12, 0, 0, mediaCtlConfig);
+     return OK;
+  }
   // isp input pad format and selection config
   addFormatParams(IspName, ispInWidth, ispInHeight, ispSinkPad, ispInFormat,

0, 0, mediaCtlConfig);
   addSelectionParams(IspName, ispInWidth, ispInHeight, 0, 0,
V4L2_SEL_TGT_CROP, ispSinkPad, mediaCtlConfig);

......
&i2c3 {

   status = "okay";
   clock-frequency = <400000>;
   rk628_csi: rk628_csi@50 {
      reg = <0x50>;

      compatible = "rockchip,rk628-dsi-v4l2";
      status = "okay";
      power-domains = <&power RK3588_PD_VI>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_pin>;
      interrupt-parent = <&gpio1>;
      interrupts = <RK_PB2 IRQ_TYPE_LEVEL_HIGH>;
      enable-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio1 RK_PB1 GPIO_ACTIVE_HIGH>;
      plugin-det-gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_LOW>;

      rockchip,camera-module-index = <0>;

      rockchip,camera-module-facing = "back";
      rockchip,camera-module-name = "HDMI-MIPI2";
      rockchip,camera-module-lens-name = "RK628-CSI";

      multi-dev-info {
         dev-idx-l = <2>;
         dev-idx-r = <4>;
         combine-idx = <2>;
         pixel-offset = <0>;
         dev-num = <2>;
      };

      port {

         hdmiin_out1: endpoint {
           remote-endpoint = <&hdmi_mipi2_in>;
           data-lanes = <1 2 3 4>;
         };
      };
   };
};
......

&i2c4 {
   pinctrl-names = "default";
   pinctrl-0 = <&i2c4m1_xfer>;

   clock-frequency = <400000>;
   status = "okay";

   rk628_bt1120: rk628_bt1120@50 {
      compatible = "rockchip,rk628-bt1120-v4l2";
      reg = <0x50>;
      status = "disabled";
      pinctrl-names = "default";
      pinctrl-0 = <&cif_dvp_clk &cif_dvp_bus16 &cif_dvp_bus8>;
      interrupt-parent = <&gpio2>;
      interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;

      enable-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio2 RK_PB0 GPIO_ACTIVE_LOW>;
      plugin-det-gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_LOW>;
      rockchip,camera-module-index = <0>;
      rockchip,camera-module-facing = "back";
      rockchip,camera-module-name = "RK628-BT1120";
      rockchip,camera-module-lens-name = "NC";
      dual-edge = <1>;

      port {
         lt8619c_out: endpoint {
           remote-endpoint = <&cif_para_in>;

           bus-width = <16>;
           pclk-sample = <1>;
         };
      };
   };
};

&rkcif_dvp {
   status = "okay";

   port {
      /* Parallel bus endpoint */
      cif_para_in: endpoint {

         remote-endpoint = <&lt8619c_out>;
      };
   };
};

&rkcif {
   status = "okay";
};

&rkcif_mmu {
   status = "okay";
};

           reset-gpios = <&gpio7 RK_PB4 GPIO_ACTIVE_LOW>;
           plugin-det-gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;

           power-gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
+          hdcp-enable = <1>;

           reset-gpios = <&gpio7 RK_PB4 GPIO_ACTIVE_LOW>;
           plugin-det-gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
           power-gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;

+          scaler-en = <1>;

csi->csi_lanes_in_use = USE_4_LANES;

continues-clk = <1>;

&i2c3 {
   status = "okay";

   clock-frequency = <400000>;

   rk628_csi: rk628_csi@50 {
      reg = <0x50>;
      compatible = "rockchip,rk628-csi-v4l2";
      status = "okay";
      power-domains = <&power RK3588_PD_VI>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_pin>;
      interrupt-parent = <&gpio1>;
      interrupts = <RK_PB2 IRQ_TYPE_LEVEL_HIGH>;
      enable-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio1 RK_PB1 GPIO_ACTIVE_HIGH>;

      plugin-det-gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_LOW>;
      continues-clk = <1>;

      rockchip,camera-module-index = <0>;
      rockchip,camera-module-facing = "back";
      rockchip,camera-module-name = "HDMI-MIPI2";
      rockchip,camera-module-lens-name = "RK628-CSI";

      multi-dev-info {
         dev-idx-l = <2>;
         dev-idx-r = <4>;
         combine-idx = <2>;

         pixel-offset = <0>;
         dev-num = <2>;
      };

      port {
         hdmiin_out1: endpoint {
           remote-endpoint = <&hdmi_mipi2_in>;
           data-lanes = <1 2 3 4>;
         };
      };
   };
};

--- a/arch/arm64/boot/dts/rockchip/rk3399-vop-clk-set.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-vop-clk-set.dtsi
@@ -148,7 +148,7 @@

                  <50000000>, <100000000>,
                  <75000000>, <75000000>,
                  <816000000>, <816000000>,
-                 <600000000>, <200000000>,
+                 <650000000>, <200000000>,
                  <800000000>, <150000000>,
                  <75000000>, <37500000>,
                  <300000000>, <100000000>,

--- a/drivers/media/platform/rockchip/isp1/dev.c
+++ b/drivers/media/platform/rockchip/isp1/dev.c
@@ -757,7 +757,7 @@ static const unsigned int rk3368_isp_clk_rate[] = {


 /* isp clock adjustment table (MHz) */
 static const unsigned int rk3399_isp_clk_rate[] = {
-     300, 400, 600
+     300, 400, 650
 };

 static struct isp_irqs_data rk1808_isp_irqs[] = {

--- a/drivers/media/platform/rockchip/isp1/dev.c
+++ b/drivers/media/platform/rockchip/isp1/dev.c
@@ -849,7 +849,7 @@ static const unsigned int rk1808_isp_clk_rate[] = {


 /* isp clock adjustment table (MHz) */
static const unsigned int rk3288_isp_clk_rate[] = {
-     150, 384, 500, 594
+     594
 };

#define RK628_CSI_PIXEL_RATE_HIGH 600000000
...


static int rk628_csi_set_fmt(struct v4l2_subdev *sd,
           struct v4l2_subdev_pad_config *cfg,
           struct v4l2_subdev_format *format)
{
...
      if ((mode->width == 3840) && (mode->height == 2160)) {
           v4l2_dbg(1, debug, sd,
                 "%s res wxh:%dx%d, link freq:%llu, pixrate:%u\n",
                 __func__, mode->width, mode->height,
                 link_freq_menu_items[1], RK628_CSI_PIXEL_RATE_HIGH);
           __v4l2_ctrl_s_ctrl(csi->link_freq, 1);
           __v4l2_ctrl_s_ctrl_int64(csi->pixel_rate,

                 RK628_CSI_PIXEL_RATE_HIGH);
      }
...
}

drivers/media/platform/rockchip/isp1/dev.c

static int __isp_pipeline_s_isp_clk(struct rkisp1_pipeline *p)

{
...
      ctrl = v4l2_ctrl_find(sd->ctrl_handler, V4L2_CID_PIXEL_RATE);
      if (!ctrl) {
           v4l2_warn(sd, "No pixel rate control in subdev\n");
           return -EPIPE;
      }

      /* calculate data rate */
      data_rate = v4l2_ctrl_g_ctrl_int64(ctrl) *
              dev->isp_sdev.in_fmt.bus_width;
      data_rate >>= 3;
      do_div(data_rate, 1000 * 1000);


      /* increase 25% margin */
      data_rate += data_rate >> 2;
...
}

[ 228.999567] rkisp1: MIPI mis error: 0x00800000
[ 228.999925] rkisp1: CIF_ISP_PIC_SIZE_ERROR (0x00000001)
[ 228.999976] rkisp1: CIF_ISP_PIC_SIZE_ERROR (0x00000001)rkisp1:

CIF_ISP_PIC_SIZE_ERROR (0x00000001)
[ 229.000081] rkisp1: CIF_ISP_PIC_SIZE_ERROR (0x00000001)rkisp1:
CIF_ISP_PIC_SIZE_ERROR (0x00000001)
[ 229.000187] rkisp1: CIF_ISP_PIC_SIZE_ERROR (0x00000001)rkisp1:
CIF_ISP_PIC_SIZE_ERROR (0x00000001)
[ 229.000294] rkisp1: CIF_ISP_PIC_SIZE_ERROR (0x00000001)rkisp1:
CIF_ISP_PIC_SIZE_ERROR (0x00000001)

CONFIG_CMA=y
CONFIG_CMA_SIZE_MBYTES=128

&isp_mmu {
      status = "disabled";

};

static u8 rk628f_edid_init_data[] = {
   0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00,
   0x24, 0xD0, 0x8F, 0x62, 0x01, 0x00, 0x00, 0x00,

   0x2D, 0x21, 0x01, 0x03, 0x80, 0x78, 0x44, 0x78,
   0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
   0x09, 0x48, 0x4C, 0x21, 0x08, 0x00, 0x61, 0x40,
   0x01, 0x01, 0x81, 0x00, 0x95, 0x00, 0xA9, 0xC0,
   0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x08, 0xE8,
   0x00, 0x30, 0xF2, 0x70, 0x5A, 0x80, 0xB0, 0x58,
   0x8A, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E,
   0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40,
   0x58, 0x2C, 0x45, 0x00, 0xB9, 0xA8, 0x42, 0x00,
   0x00, 0x1E, 0x00, 0x00, 0x00, 0xFC, 0x00, 0x49,
   0x46, 0x50, 0x20, 0x44, 0x69, 0x73, 0x70, 0x6C,

   0x61, 0x79, 0x0A, 0x20, 0x00, 0x00, 0x00, 0xFD,
   0x00, 0x3B, 0x46, 0x1F, 0x8C, 0x3C, 0x00, 0x0A,
   0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0xA8,

   0x02, 0x03, 0x39, 0xF2, 0x4D, 0x01, 0x03, 0x12,
   0x13, 0x84, 0x22, 0x1F, 0x90, 0x5D, 0x5E, 0x5F,
   0x60, 0x61, 0x23, 0x09, 0x07, 0x07, 0x83, 0x01,
   0x00, 0x00, 0x6D, 0x03, 0x0C, 0x00, 0x10, 0x00,
   0x00, 0x44, 0x20, 0x00, 0x60, 0x03, 0x02, 0x01,
   0x67, 0xD8, 0x5D, 0xC4, 0x01, 0x78, 0xC0, 0x00,
   0xE3, 0x05, 0x03, 0x01, 0xE4, 0x0F, 0x00, 0x18,
   0x00, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D,

   0x40, 0x58, 0x2C, 0x45, 0x00, 0xB9, 0xA8, 0x42,
   0x00, 0x00, 0x1E, 0x08, 0xE8, 0x00, 0x30, 0xF2,
   0x70, 0x5A, 0x80, 0xB0, 0x58, 0x8A, 0x00, 0xC4,
   0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00,
   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x93,
};

hardware/rockchip/camera/etc/camera/camera3_profiles_rk3xxx.xml

</Profiles>
<Profiles cameraId="0" name="rk628-csi" moduleId="m00">
    <Supported_hardware>
        <hwType value="SUPPORTED_HW_RKISP1"/>

&rk628_csi {
    status = "okay";
    /*
     * If the hpd output level is inverted on the circuit,
     * the following configuration needs to be enabled.
     */
    /* hpd-output-inverted; */
    plugin-det-gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
    power-gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
    rockchip,camera-module-index = <0>;
    rockchip,camera-module-facing = "back";
    rockchip,camera-module-name = "RK628-CSI";
    rockchip,camera-module-lens-name = "NC";

<scaler.availableStreamConfigurations value="BLOB,3840x2160,OUTPUT,
    BLOB,1920x1080,OUTPUT,
    BLOB,1280x720,OUTPUT,
    BLOB,720x576,OUTPUT,
    BLOB,720x480,OUTPUT,
    YCbCr_420_888,3840x2160,OUTPUT,
    YCbCr_420_888,1920x1080,OUTPUT,
    YCbCr_420_888,1280x720,OUTPUT,
    YCbCr_420_888,720x576,OUTPUT,
    YCbCr_420_888,720x480,OUTPUT,
    IMPLEMENTATION_DEFINED,3840x2160,OUTPUT,
    IMPLEMENTATION_DEFINED,1920x1080,OUTPUT,
    IMPLEMENTATION_DEFINED,1280x720,OUTPUT,
    IMPLEMENTATION_DEFINED,720x576,OUTPUT,
    IMPLEMENTATION_DEFINED,720x480,OUTPUT" />
<scaler.availableMinFrameDurations value="BLOB,3840x2160,33333333,
    BLOB,1920x1080,16666667,
    BLOB,1280x720,16666667,
    BLOB,720x576,20000000,
    BLOB,720x480,16666667,
    YCbCr_420_888,3840x2160,33333333,
    YCbCr_420_888,1920x1080,16666667,
    YCbCr_420_888,1280x720,16666667,
    YCbCr_420_888,720x576,20000000,
    YCbCr_420_888,720x480,16666667,
    IMPLEMENTATION_DEFINED,3840x2160,33333333,
    IMPLEMENTATION_DEFINED,1920x1080,16666667,
    IMPLEMENTATION_DEFINED,1280x720,16666667,
    IMPLEMENTATION_DEFINED,720x576,20000000,
    IMPLEMENTATION_DEFINED,720x480,16666667"/>
<scaler.availableStallDurations value="BLOB,3840x2160,33333333,
    BLOB,1920x1080,16666667,
    BLOB,1280x720,16666667,
    BLOB,720x576,20000000,
    BLOB,720x480,16666667"/>

<sensor.maxAnalogSensitivity value="2400"/>
<sensor.orientation value="0"/>
<sensor.profileHueSatMapDimensions value="0,0,0"/>

RKDocs/common/hdmi-in/apk/rkCamera2_based_on_CameraHal3_V1.3.tar.gz

packages/apps/

diff --git a/device.mk b/device.mk
index 6667b5c..96f08f1 100644

--- a/device.mk
+++ b/device.mk
@@ -17,7 +17,8 @@
 PRODUCT_PACKAGES += \
   memtrack.$(TARGET_BOARD_PLATFORM) \
   WallpaperPicker \
-  Launcher3
+  Launcher3 \
+  rkCamera2

 #$_rbox_$_modify_$_zhengyang: add displayd
 PRODUCT_PACKAGES += \

rkCamera2/jni/native.cpp

static void openDevice(JNIEnv *env, jobject thiz)
{
    (void)*env;
    (void)thiz;

    char video_name[64];
    memset(video_name, 0, sizeof(video_name));
    strcat(video_name, "/dev/v4l-subdev2");

    camFd = open(video_name, O_RDWR);
    if (camFd < 0) {
        LOGE("open %s failed,erro=%s",video_name,strerror(errno));
    } else {
        LOGD("open %s success,fd=%d",video_name,camFd);
    }
}

static void getDeviceFormat(int *format)
{
    struct v4l2_control control;
    memset(&control, 0, sizeof(struct v4l2_control));
    control.id = V4L2_CID_DV_RX_POWER_PRESENT;
    int err = ioctl(camFd, VIDIOC_G_CTRL, &control);
    if (err < 0) {
        LOGV("Set POWER_PRESENT failed ,%d(%s)", errno, strerror(errno));
    }

    unsigned int noSignalAndSync = 0;
    ioctl(camFd, VIDIOC_G_INPUT, &noSignalAndSync);
    LOGV("noSignalAndSync ? %s",noSignalAndSync?"YES":"NO");

    struct v4l2_dv_timings dv_timings;
    memset(&dv_timings, 0 ,sizeof(struct v4l2_dv_timings));
    err = ioctl(camFd, VIDIOC_SUBDEV_QUERY_DV_TIMINGS, &dv_timings);
    if (err < 0) {
        LOGV("Set VIDIOC_SUBDEV_QUERY_DV_TIMINGS failed ,%d(%s)", errno, strerror(errno));
    }

    format[0] = dv_timings.bt.width;
    format[1] = dv_timings.bt.height;
    format[2] = control.value && !noSignalAndSync;
}

rk3288:/ # getenforce
Enforcing
rk3288:/ # setenforce 0
rk3288:/ #
rk3288:/ # getenforce
Permissive

rk3288:/ #
rk3288:/ # dumpsys media.camera

== Service global info: ==

Number of camera devices: 1
Number of normal camera devices: 1
    Device 0 maps to "0"
Active Camera Clients:
[]
Allowed user IDs: 0

== Camera service events log (most recent at top): ==
  04-08 11:08:31 : USER_SWITCH previous allowed user IDs: <None>, current allowed user IDs: 0
  01-18 08:50:15 : ADD device 0, reason: (Device status changed from 0 to 1)
  01-18 08:50:15 : ADD device 0, reason: (Device added)

vim device/rockchip/rk3588/BoardConfig.mk
BOARD_HDMI_IN_SUPPORT := true

vim device/rockchip/rk3588/BoardConfig.mk
CAMERA_SUPPORT_HDMI := true

PRODUCT_PACKAGES += \
   rkCamera2

setprop vendor.tvinput.hdmiin.type 1

setprop persist.sys.hdmiinmode 2

hardware/rockchip/camera/etc/tools/

media-ctl -d /dev/media0 –p

...
- entity 8: m00_b_rk628-csi rk628-csi (1 pad, 1 link)
         type V4L2 subdev subtype Sensor

         device node name /dev/v4l-subdev2
      pad0: Source
           [fmt:UYVY2X8/1920x1080]
           -> "rockchip-mipi-dphy-rx":0 [ENABLED]
...

media-ctl -d /dev/media0 -l \
'"m00_b_rk628-csi rk628-csi":0->"rockchip-mipi-dphy-rx":0 [1]'

media-ctl -d /dev/media0 -l \
'"rockchip-mipi-dphy-rx":1->"rkisp1-isp-subdev":0 [1]'
media-ctl -d /dev/media0 -l '"rkisp1-input-params":0->"rkisp1-isp-subdev":1 [1]'
media-ctl -d /dev/media0 -l '"rkisp1-isp-subdev":2->"rkisp1_mainpath":0 [1]'
media-ctl -d /dev/media0 -l '"rkisp1-isp-subdev":2->"rkisp1_selfpath":0 [1]'
media-ctl -d /dev/media0 -l '"rkisp1-isp-subdev":3->"rkisp1-statistics":0 [1]'

media-ctl -d /dev/media0 \
--set-v4l2 '"rkisp1-isp-subdev":0[fmt:UYVY2X8/1920x1080]'
media-ctl -d /dev/media0 \

--set-v4l2 '"rkisp1-isp-subdev":0[crop:(0,0)/1920x1080]'
media-ctl -d /dev/media0 \
--set-v4l2 '"rkisp1-isp-subdev":2[fmt:UYVY2X8/1920x1080]'
media-ctl -d /dev/media0 \
--set-v4l2 '"rkisp1-isp-subdev":2[crop:(0,0)/1920x1080]'

media-ctl -d /dev/media0 –p

v4l2-ctl --verbose -d /dev/video0 --set-fmt-
video=width=1920,height=1080,pixelformat='NV12' --stream-mmap=4

v4l2-ctl -d /dev/video0 --set-fmt-video=width=1920,height=1080,pixelformat='NV12'
--stream-mmap=3 --stream-skip=4 --stream-to=/data/1920x1080p60_nv12.yuv --stream-
count=5 --stream-poll

VIDIOC_QUERYCAP: ok
VIDIOC_G_FMT: ok
VIDIOC_S_FMT: ok

Format Video Capture Multiplanar:
      Width/Height : 1920/1080
      Pixel Format : 'NV12'
      Field        : None
      Number of planes : 1
      Flags        :
      Colorspace   : Default
      Transfer Function : Default
      YCbCr Encoding : Default
      Quantization : Full Range
      Plane 0      :
        Bytes per Line : 1920
        Size Image : 3110400

VIDIOC_G_SELECTION: ok
VIDIOC_S_SELECTION: ok
VIDIOC_REQBUFS: ok
VIDIOC_QUERYBUF: ok
VIDIOC_QUERYBUF: ok
VIDIOC_QBUF: ok
VIDIOC_QUERYBUF: ok
VIDIOC_QBUF: ok
VIDIOC_QUERYBUF: ok
VIDIOC_QBUF: ok
VIDIOC_QUERYBUF: ok
VIDIOC_QBUF: ok

VIDIOC_STREAMON: ok
idx: 0 seq: 0 bytesused: 3110400 ts: 131.560377
idx: 1 seq: 1 bytesused: 3110400 ts: 131.577023 delta: 16.646 ms
idx: 2 seq: 2 bytesused: 3110400 ts: 131.593697 delta: 16.674 ms
idx: 3 seq: 3 bytesused: 3110400 ts: 131.610363 delta: 16.666 ms
idx: 0 seq: 4 bytesused: 3110400 ts: 131.627033 delta: 16.670 ms fps: 60.01
idx: 1 seq: 5 bytesused: 3110400 ts: 131.643721 delta: 16.688 ms fps: 59.99
idx: 2 seq: 6 bytesused: 3110400 ts: 131.660390 delta: 16.669 ms fps: 59.99
idx: 3 seq: 7 bytesused: 3110400 ts: 131.677058 delta: 16.668 ms fps: 59.99

echo 1 > /sys/kernel/debug/rk628/x-0050/debug //x为挂载的i2c总线，50为对应的i2c地址
echo 2 > /sys/module/rk628_csi/parameters/debug
echo 2 > /sys/module/rk628_csi_v4l2/parameters/debug //内核为linux4.4或者4.19

dmesg -n 8

diff --git a/drivers/media/i2c/rk628_csi.c b/drivers/media/i2c/rk628_csi.c
index c763a9558169..bd7f3effb45a 100644
--- a/drivers/media/i2c/rk628_csi_v4l2.c

+++ b/drivers/media/i2c/rk628_csi_v4l2.c
@@ -34,7 +34,7 @@
 #include <video/videomode.h>
 #include "rk628_csi.h"

-static int debug;
+static int debug = 1;
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "debug level (0-3)");

diff --git a/include/media/v4l2-common.h b/include/media/v4l2-common.h
index 1cc0c5ba16b3..e74f3a85f0b8 100644
--- a/include/media/v4l2-common.h

+++ b/include/media/v4l2-common.h
@@ -75,7 +75,7 @@
 #define v4l2_dbg(level, debug, dev, fmt, arg...)   \
      do {                                          \
           if (debug >= (level))                    \
-                v4l2_printk(KERN_DEBUG, dev, fmt , ## arg); \
+                v4l2_printk(KERN_INFO, dev, fmt , ## arg); \
      } while (0)

console:/ # ls /sys/kernel/debug/rk628/3-0050/registers/
adapter combtxphy csi dsi0 gpio0 gpio2 grf hdmirxphy

combrxphy cru   csi1 dsi1 gpio1 gpio3 hdmirx

console:/ # cat /sys/kernel/debug/rk628/3-0050/registers/cru
rk628_cru:


0xc0000: 00001031 00000441 00800000 00000007
0xc0010: 00007f00
0xc0020: 00001028 00000441 00f5c28f 00000007
0xc0030: 00007f00
0xc0040: 00005019 00000541 0099735e 00000007
0xc0050: 00007f00
0xc0060: 00000015
0xc0080: 00008989 00000003 00000007 00004b80
0xc0090: 03355460 000080d7 00008004 0000003b
0xc00a0: 00002c00 00000000 00000000 00000000
0xc00b0: 00285f58 00010008 00010008 00000103
0xc00c0: 00000300 00000703 0000000b 00000008

0xc00d0: 0001000a 00000b07
0xc0180: 00000000 00000000 00000000 00000000
0xc0190: 00000000 00000000
0xc0200: 00000000 00000000 00000000 00000000
0xc0210: 00000000

rk3288:/ # echo 0x000 0xffffffff > /sys/kernel/debug/rk628/3-0050/registers/grf

console:/ # cat /sys/kernel/debug/rk628/3-0050/hdmirx/status
status: plugin

Clk-Ch:Lock Ch0:Lock   Ch1:Lock    Ch2:Lock
Color Format: RGB
Timing: 1920x1080p60 (2200x1125)   hfp:88 hs:45 hbp:147 vfp:4
vs:5 vbp:36
Pixel Clk: 148500000
Mode: HDMI
Color Depth: 8 bit
Color Range: Limited
Color Space: RGB

echo 1 > /sys/kernel/debug/rk628/3-0050/scaler_color_bar

//pattern 模式选择

echo 2 > /sys/kernel/debug/rk628/3-0050/scaler_color_bar

rk628_dc: rk628-dc {
      compatible = "rockchip,dummy-codec";
      #sound-dai-cells = <0>;

};

hdmiin-sound {
      compatible = "simple-audio-card";
      simple-audio-card,format = "i2s";
      simple-audio-card,name = "rockchip,hdmiin";
      simple-audio-card,bitclock-master = <&dailink0_master>;
      simple-audio-card,frame-master = <&dailink0_master>;
      status = "okay";
      simple-audio-card,cpu {
                 sound-dai = <&i2s0>;
      };

      dailink0_master: simple-audio-card,codec {
                 sound-dai = <&rk628_dc>;
      };
};

--- a/drivers/media/i2c/rk628/rk628_hdmirx.h
+++ b/drivers/media/i2c/rk628/rk628_hdmirx.h
@@ -392,5 +392,5 @@ bool rk628_audio_ctsnints_enabled(HAUDINFO info);
 void rk628_csi_isr_ctsn(HAUDINFO info, u32 pdec_ints);

 void rk628_csi_isr_fifoints(HAUDINFO info, u32 fifo_ints);
 int rk628_is_avi_ready(struct rk628 *rk628, bool avi_rcv_rdy);
+void rk628_hdmirx_audio_set_mclk_output(HAUDINFO info);

--- a/drivers/media/i2c/rk628/rk628_csi.c
+++ b/drivers/media/i2c/rk628/rk628_csi.c
@@ -957,6 +957,9 @@ static void rk628_csi_initial_setup(struct rk628_csi *csi)
 {
      struct v4l2_subdev_edid def_edid;

+     //enable rk628 mclk
+     rk628_hdmirx_audio_set_mclk_output(csi->audio_info);


--- a/drivers/media/i2c/rk628/rk628_csi_v4l2.c
+++ b/drivers/media/i2c/rk628/rk628_csi_v4l2.c
@@ -1096,6 +1096,9 @@ static void rk628_csi_initial_setup(struct v4l2_subdev *sd)
      struct rk628_csi *csi = to_csi(sd);
      struct v4l2_subdev_edid def_edid;

+     //enable rk628 mclk
+     rk628_hdmirx_audio_set_mclk_output(csi->audio_info);

hdmiin-sound {
      compatible = "rockchip,rockchip-rt5651-rk628-sound";
      rockchip,cpu = <&i2s>;

      rockchip,codec = <&rt5651>;
      status = "okay";
};

&i2c4 {
      clock-frequency = <400000>;
      status = "okay";

      rk628_csi_v4l2: rk628_csi_v4l2@50 {
           reg = <0x50>;
           compatible = "rockchip,rk628-csi-v4l2";
           ....
           i2s-enable-default;
           ....
      };
};

hdmi_sound: hdmi-sound {
      compatible = "simple-audio-card";
      simple-audio-card,format = "i2s";

      simple-audio-card,name = "hdmi-sound";
      status = "okay";
      simple-audio-card,cpu {
           sound-dai = <&i2s0>;
      };
      simple-audio-card,codec {
           sound-dai = <&rk628_hdmi>;
      };
};

echo 0x000 0x6000220 > /sys/kernel/debug/regmap/0-0050-grf/registers //i2s 的
IOMUX

echo 0x70 0xfffff55c > /sys/kernel/debug/regmap/0-0050-grf/registers
echo 0x70 0x155c155c > /sys/kernel/debug/regmap/0-0050-grf/registers // 设置输出

diff --git a/drivers/media/i2c/rk628_csi.c b/drivers/media/i2c/rk628_csi.c
index 5e8e3710a82f..638ac2acc472 100644

--- a/drivers/media/i2c/rk628_csi.c
+++ b/drivers/media/i2c/rk628_csi.c
@@ -34,7 +34,7 @@
 #include <video/videomode.h>
 #include "rk628_csi.h"

-static int debug;
+static int debug = 3;
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "debug level (0-3)");

diff --git a/include/media/v4l2-common.h b/include/media/v4l2-common.h
index cdc87ec61e54..f159118d4a6b 100644

--- a/include/media/v4l2-common.h
+++ b/include/media/v4l2-common.h
@@ -82,7 +82,7 @@
 #define v4l2_dbg(level, debug, dev, fmt, arg...)   \
      do {                                          \
           if (debug >= (level))                    \
-                v4l2_printk(KERN_DEBUG, dev, fmt , ## arg); \
+                v4l2_printk(KERN_INFO, dev, fmt , ## arg); \
      } while (0)


 /**

m00_b_rk628-csi rk628-csi: rk628_hdmirx_audio_fs: clkrate:1500 tmdsclk:74250000,
n_decoded:6144, cts_decoded:74250, fs_audio:48000

m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_FILLSTS1:0xfe, single offset:0, total offset:-2
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_ISTS:0x4
m00_b_rk628-csi rk628-csi: rk628_hdmirx_audio_fs: clkrate:1500 tmdsclk:74250000,
n_decoded:6144, cts_decoded:74250, fs_audio:48000
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_FILLSTS1:0xfc, single offset:-2, total offset:-4
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_ISTS:0x4
m00_b_rk628-csi rk628-csi: rk628_hdmirx_audio_fs: clkrate:1500 tmdsclk:74250000,
n_decoded:6144, cts_decoded:74250, fs_audio:48000
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:

HDMI_RX_AUD_FIFO_FILLSTS1:0xfc, single offset:0, total offset:-4
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_ISTS:0x4
m00_b_rk628-csi rk628-csi: rk628_hdmirx_audio_fs: clkrate:1500 tmdsclk:74250000,
n_decoded:6144, cts_decoded:74250, fs_audio:48000
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_FILLSTS1:0xfc, single offset:0, total offset:-4
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_ISTS:0x4
m00_b_rk628-csi rk628-csi: rk628_hdmirx_audio_fs: clkrate:1500 tmdsclk:74250000,
n_decoded:6144, cts_decoded:74250, fs_audio:48000
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:

HDMI_RX_AUD_FIFO_FILLSTS1:0xfa, single offset:-2, total offset:-6
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_ISTS:0x4
m00_b_rk628-csi rk628-csi: rk628_hdmirx_audio_fs: clkrate:1500 tmdsclk:74250000,
n_decoded:6144, cts_decoded:74250, fs_audio:48000
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_FILLSTS1:0xfc, single offset:2, total offset:-4
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_ISTS:0x4
m00_b_rk628-csi rk628-csi: rk628_hdmirx_audio_fs: clkrate:1500 tmdsclk:74250000,
n_decoded:6144, cts_decoded:74250, fs_audio:48000
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:
HDMI_RX_AUD_FIFO_FILLSTS1:0xfa, single offset:-2, total offset:-6
m00_b_rk628-csi rk628-csi: rk628_csi_delayed_work_audio:

HDMI_RX_AUD_FIFO_ISTS:0x4

getprop vendor.hdmiin.audiorate

 static void rk628_hdmirx_initial_setup(struct rk628_hdmirx *hdmirx)
 {
      struct v4l2_subdev_edid def_edid;

@@ -783,6 +937,8 @@ static void rk628_hdmirx_initial_setup(struct rk628_hdmirx
*hdmirx)

      // ddc and hpd pinctrl
      regmap_write(hdmirx->grf, GRF_GPIO1AB_SEL_CON, 0x07000700);
+     //i2s pinctrl
+     regmap_write(hdmirx->grf, GRF_GPIO0AB_SEL_CON, 0x155c155c);

      rk628_hdmirx_controller_reset(hdmirx);

git sholsh@rk-intel-1:~/rk-sdk/android11-rk3399/kernel$ git show
007131063748ea69facbf4bbe7aaee71c34fd921

commit 007131063748ea69facbf4bbe7aaee71c34fd921
Author: Shunhua Lan <lsh@rock-chips.com>
Date: Fri Apr 23 18:43:59 2021 +0800

   media: i2c: rk628csi: fix mask for clkrate and fs audio align to 100

   Signed-off-by: Shunhua Lan <lsh@rock-chips.com>
   Change-Id: I15b290319463f1b41e6908e54caa99ef9c6db4f4

diff --git a/drivers/media/i2c/rk628_csi.c b/drivers/media/i2c/rk628_csi.c
index 89c4a926a985..a970bc621e0e 100644
--- a/drivers/media/i2c/rk628_csi.c
+++ b/drivers/media/i2c/rk628_csi.c

@@ -1064,7 +1064,7 @@ static void rk628_csi_delayed_work_audio(struct work_struct
*work)

      /* fout=128*fs=ftmds*N/CTS */
      regmap_read(csi->hdmirx_regmap, HDMI_RX_HDMI_CKM_RESULT, &clkrate);
-     clkrate = clkrate & 0xfff;
+     clkrate = clkrate & 0xffff;
      /* tmdsclk = (clkrate/1000) * 49500000 */
      tmdsclk = clkrate * (49500000 / 1000);
      regmap_read(csi->hdmirx_regmap, HDMI_RX_PDEC_ACR_CTS, &cts_decoded);
@@ -1073,6 +1073,8 @@ static void rk628_csi_delayed_work_audio(struct work_struct

*work)
      if (cts_decoded != 0) {
           fs_audio = div_u64((tmdsclk * n_decoded), cts_decoded);
           fs_audio = div_u64(fs_audio, 128);
+          fs_audio = div_u64(fs_audio + 50, 100);
+          fs_audio *= 100;
      }
      v4l2_dbg(2, debug, sd,
           "%s: clkrate:%d tmdsclk:%llu, n_decoded:%d, cts_decoded:%d,
fs_audio:%llu\n",

[67.440094] m00_b_rk628-csi rk628-csi:rk628_csi_delayed_work_audio:clkrate:1904
tmdsclk:94248000,n_decoded:6144,cts_decoded:297000,fs_audio:15232

grf: gpio0 相关 iomux 切换，配置为 IO 口:
echo 0x70 0x0fff0000 > registers


gpio0 配置为输出口, 1-0051-rk628-pinctrl:
echo 0xd0008 0x00EC00EC > registers

grf，选择在哪一级拉出信号:
HDMI_RX:
echo 0x300 0x11 > registers
ASYNC_IN:
echo 0x300 0x14 > registers
ASYNC_OUT:
echo 0x300 0x15 > registers
SCALER：
echo 0x300 0x16 > registers

static struct rockchip_mux_route_data rk3568_mux_route_data[] = {
   ....
   RK_MUXROUTE_GRF(1, RK_PA2, 1, 0x0310, WRITE_MASK_VAL(11, 10, 0)), /* I2S1 IO

mux M0 */
   RK_MUXROUTE_GRF(3, RK_PC6, 4, 0x0310, WRITE_MASK_VAL(11, 10, 1)), /* I2S1 IO
mux M1 */
   RK_MUXROUTE_GRF(2, RK_PD0, 5, 0x0310, WRITE_MASK_VAL(11, 10, 2)), /* I2S1 IO
mux M2 */
   RK_MUXROUTE_GRF(2, RK_PC1, 1, 0x0310, WRITE_MASK_VAL(12, 12, 0)), /* I2S2 IO
mux M0 */
   RK_MUXROUTE_GRF(4, RK_PB6, 5, 0x0310, WRITE_MASK_VAL(12, 12, 1)), /* I2S2 IO
mux M1 */
   RK_MUXROUTE_GRF(3, RK_PA4, 4, 0x0310, WRITE_MASK_VAL(14, 14, 0)), /* I2S3 IO
mux M0 */
   RK_MUXROUTE_GRF(4, RK_PC4, 5, 0x0310, WRITE_MASK_VAL(14, 14, 1)), /* I2S3 IO
mux M1 */

   ....
}

diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-
rockchip.c

index 871c49ef0c2a..3d10e6c2ed27 100644
--- a/drivers/pinctrl/pinctrl-rockchip.c
+++ b/drivers/pinctrl/pinctrl-rockchip.c
@@ -1046,13 +1046,26 @@ static struct rockchip_mux_route_data
rk3568_mux_route_data[] = {
      RK_MUXROUTE_GRF(2, RK_PB0, 3, 0x0310, WRITE_MASK_VAL(9, 8, 0)), /* UART9
IO mux M0 */
      RK_MUXROUTE_GRF(4, RK_PC5, 4, 0x0310, WRITE_MASK_VAL(9, 8, 1)), /* UART9
IO mux M1 */
      RK_MUXROUTE_GRF(4, RK_PA4, 4, 0x0310, WRITE_MASK_VAL(9, 8, 2)), /* UART9

IO mux M2 */
+
      RK_MUXROUTE_GRF(1, RK_PA2, 1, 0x0310, WRITE_MASK_VAL(11, 10, 0)), /* I2S1
IO mux M0 */
      RK_MUXROUTE_GRF(3, RK_PC6, 4, 0x0310, WRITE_MASK_VAL(11, 10, 1)), /* I2S1
IO mux M1 */
      RK_MUXROUTE_GRF(2, RK_PD0, 5, 0x0310, WRITE_MASK_VAL(11, 10, 2)), /* I2S1
IO mux M2 */
+     RK_MUXROUTE_GRF(1, RK_PA3, 1, 0x0310, WRITE_MASK_VAL(11, 10, 0)), /* I2S1
IO mux sclk tx M0 */
+     RK_MUXROUTE_GRF(1, RK_PA4, 1, 0x0310, WRITE_MASK_VAL(11, 10, 0)), /* I2S1
IO mux sclk rx M0 */

+     RK_MUXROUTE_GRF(3, RK_PC7, 4, 0x0310, WRITE_MASK_VAL(11, 10, 1)), /* I2S1
IO mux sclk tx M1 */
+     RK_MUXROUTE_GRF(4, RK_PA6, 5, 0x0310, WRITE_MASK_VAL(11, 10, 1)), /* I2S1
IO mux sclk rx M1 */
+     RK_MUXROUTE_GRF(2, RK_PD1, 5, 0x0310, WRITE_MASK_VAL(11, 10, 2)), /* I2S1
IO mux sclk tx M2 */
+     RK_MUXROUTE_GRF(3, RK_PC3, 5, 0x0310, WRITE_MASK_VAL(11, 10, 2)), /* I2S1
IO mux sclk rx M2 */
      RK_MUXROUTE_GRF(2, RK_PC1, 1, 0x0310, WRITE_MASK_VAL(12, 12, 0)), /* I2S2
IO mux M0 */
      RK_MUXROUTE_GRF(4, RK_PB6, 5, 0x0310, WRITE_MASK_VAL(12, 12, 1)), /* I2S2
IO mux M1 */
+     RK_MUXROUTE_GRF(2, RK_PC2, 1, 0x0310, WRITE_MASK_VAL(12, 12, 0)), /* I2S2

IO mux sclk tx M0 */
+     RK_MUXROUTE_GRF(2, RK_PB7, 1, 0x0310, WRITE_MASK_VAL(12, 12, 0)), /* I2S2
IO mux sclk rx M0 */
+     RK_MUXROUTE_GRF(4, RK_PB7, 4, 0x0310, WRITE_MASK_VAL(12, 12, 1)), /* I2S1
IO mux sclk tx M1 */
+     RK_MUXROUTE_GRF(4, RK_PC1, 5, 0x0310, WRITE_MASK_VAL(12, 12, 1)), /* I2S1
IO mux sclk rx M1 */
      RK_MUXROUTE_GRF(3, RK_PA2, 4, 0x0310, WRITE_MASK_VAL(14, 14, 0)), /* I2S3
IO mux M0 */
      RK_MUXROUTE_GRF(4, RK_PC2, 5, 0x0310, WRITE_MASK_VAL(14, 14, 1)), /* I2S3
IO mux M1 */
+     RK_MUXROUTE_GRF(3, RK_PA3, 4, 0x0310, WRITE_MASK_VAL(14, 14, 0)), /* I2S3

IO mux sclk M0 */
+     RK_MUXROUTE_GRF(4, RK_PC3, 5, 0x0310, WRITE_MASK_VAL(14, 14, 1)), /* I2S3
IO mux sclk M1 */
      RK_MUXROUTE_GRF(1, RK_PA4, 3, 0x0314, WRITE_MASK_VAL(1, 0, 0)), /* PDM IO
mux M0 */
      RK_MUXROUTE_GRF(1, RK_PA6, 3, 0x0314, WRITE_MASK_VAL(1, 0, 0)), /* PDM IO
mux M0 */
      RK_MUXROUTE_GRF(3, RK_PD6, 5, 0x0314, WRITE_MASK_VAL(1, 0, 1)), /* PDM IO
mux M1 */

console:/ # cat /proc/asound/cards
 0 [rockchiphdmi ]: rockchip_hdmi - rockchip,hdmi
                rockchip,hdmi

 1 [rockchiphdmiin ]: rockchip_hdmiin - rockchip,hdmiin
                rockchip,hdmiin

console:/ # cat /proc/asound/card1/pcm0c/sub0/status
state: RUNNING
owner_pid : 1415
trigger_time: 1632716135.151992694
tstamp   : 0.000000000
delay    : 0
avail    : 0
avail_max : 0
-----

hw_ptr   : 0
appl_ptr : 0

console:/ # cat /proc/asound/card1/pcm0c/sub0/status
state: RUNNING
owner_pid : 1421

trigger_time: 1632892868.412331044
tstamp   : 1632892881.181113577
delay    : 232
avail    : 232
avail_max : 264
-----
hw_ptr   : 543736
appl_ptr : 543504

+&i2s0 {
+     rockchip,clk-trcm = <1>;

+     status = "okay";
+};

console:/ # io -4 0xff880008
ff880008: 18071f1f

+&i2s0 {
+     rockchip,clk-trcm = <2>;
+     status = "okay";

+};
正常寄存器如下：
console:/ # io -4 0xff880008
ff880008: 28071f1f

Tx and Rx Common Use
2'b00/2'b11:tx_lrck/rx_lrck are used as synchronous signal for TX
/RX respectively.

2'b01:only tx_lrck is used as synchronous signal for TX and RX.
2'b10:only rx_lrck is used as synchronous signal for TX and RX.

09-28 07:03:13.341 261 1386 D AudioHardwareTiny: card0 id:rockchiphdmi
09-28 07:03:13.341 261 1386 D AudioHardwareTiny: SPEAKER card, got
card=0,device=0

09-28 07:03:13.341 261 1386 D AudioHardwareTiny: HDMI card, got
card=0,device=0
09-28 07:03:13.341 261 1386 D AudioHardwareTiny: SPDIF card, got
card=0,device=0
09-28 07:03:13.341 261 1386 D AudioHardwareTiny: BT card, got card=0,device=0
09-28 07:03:13.342 261 1386 D AudioHardwareTiny: card1 id:rockchiphdmiin
09-28 07:03:13.342 261 1386 D AudioHardwareTiny: SPEAKER card, got
card=1,device=0
09-28 07:03:13.342 261 1386 D AudioHardwareTiny: HDMI card, got
card=1,device=0
09-28 07:03:13.342 261 1386 D AudioHardwareTiny: SPDIF card, got
card=1,device=0

09-28 07:03:13.342 261 1386 D AudioHardwareTiny: BT card, got card=1,device=0
09-28 07:03:13.342 261 1386 D AudioHardwareTiny: No exist
proc/asound/card2/id, break and finish parsing
09-28 07:03:13.343 261 1386 D AudioHardwareTiny: dump out device info
09-28 07:03:13.343 261 1386 D AudioHardwareTiny: dev_info SPEAKER card=1,
device:0
09-28 07:03:13.343 261 1386 D AudioHardwareTiny: dev_info HDMI card=1,
device:0
09-28 07:03:13.343 261 1386 D AudioHardwareTiny: dev_info SPDIF card=1,
device:0
09-28 07:03:13.343 261 1386 D AudioHardwareTiny: dev_info BT card=1, device:0

hardware/rockchip/audio
commit 1b51a62fc62e9d63850e4e5a39f1e3cff0aa9b88 (HEAD)
Author: Shunhua Lan <lsh@rock-chips.com>

Date: Tue Sep 28 17:25:44 2021 +0800

   [audio hal] use levenshtein distance for sound card matching

   Signed-off-by: Shunhua Lan <lsh@rock-chips.com>
   Change-Id: I16f1692715d710a0693ae74875b0272669a04ba2

rk628-csi-v4l2 1-0051: clk det over cnt:10, reg_0x6654:0x403f0000
rk628-csi-v4l2 1-0051: |d2_p| level detection anomaly
rk628-csi-v4l2 1-0051: clock detected failed, cfg resistance manual!

rk628-csi-v4l2 1-0051: err, clk not stable, reg_0x6630:0x87000d,
reg_0x6608:0x110100
m00_b_rk628-csi 1-0051: hdmi rxphy power on failed

rk628-csi-v4l2 1-0051: clk det over cnt:10, reg_0x6654:0x403f0000
rk628-csi-v4l2 1-0051: Clock detection anomaly
rk628-csi-v4l2 1-0051: clock detected failed, cfg resistance manual!

rk628-csi-v4l2 1-0051: err, clk not stable, reg_0x6630:0x87000d,
reg_0x6608:0x110100
m00_b_rk628-csi 1-0051: hdmi rxphy power on failed

25175, 27000, 33750, 40000, 59400, 65000, 68250, 74250,
75000, 83500, 85500, 88750, 928125, 101000, 102250, 108000,
118800, 119000, 135000, 148500, 150000, 162000, 165000, 297000

m00_b_rk628-csi rk628-csi: cnt_num:1000, tmds_cnt:3000, hs_cnt:15, vs_cnt:3667, hofs:192
m00_b_rk628-csi rk628-csi: SCDC_REGS1:0xffff0f00, act:1920x1080, total:2200x1125, fps:60,
m00_b_rk628-csi rk628-csi: hfp:88, hs:45, hbp:147, vfp:4, vs:5, vbp:36, interlace:0
m00_b_rk628-csi rk628-csi: rk628_csi_s_dv_timings: 1920x1080p60.0 (2200x1125)
m00_b_rk628-csi rk628-csi: enable_stream: disable

D JNI     : JNI CAMERA CALL init
I HdmiInput-native: JNI OnLoad
I HdmiInput-native: Apk Version: V1.2
E HdmiInput-native: openDevice(91): open /dev/v4l-subdev2 failed,erro=Permission denied
D RockchipCamera2: remove fake pic button
D RockchipCamera2: recreateTextureview
D RockchipCamera2: textureView remove
D RockchipCamera2: onResume

rk3288:/ # cat /vendor/ueventd.rc | grep subdev
/dev/v4l-subdev*   0666 media   camera

wendingxian@ubuntu:~/rk3288_9.0_int/device/rockchip/common$ git show
commit 17112e1430b0f10a88b57c73ad19203e58f0eeff (HEAD -> mid_9.0, rk/rk/rk33/mid/9.0/develop)
Author: Dingxian Wen <shawn.wen@rock-chips.com>
Date:   Tue Apr 27 21:26:48 2021 +0800

    ueventd.rockchip.rc: modify the /dev/v4l-subdev* permission to 666

    Signed-off-by: Dingxian Wen <shawn.wen@rock-chips.com>
    Change-Id: Id4848209fd983f7e525761f19c7f0420b9fee747

diff --git a/ueventd.rockchip.rc b/ueventd.rockchip.rc
index 1914490b..52935d49 100755
--- a/ueventd.rockchip.rc
+++ b/ueventd.rockchip.rc
@@ -178,7 +178,7 @@
 /dev/ovr0                0664   system     system
 
 #for rk_isp1
-/dev/v4l-subdev*         0660   media      camera
+/dev/v4l-subdev*         0666   media      camera

 /dev/video0             0660   media      camera
 /dev/video1             0660   media      camera

rk628d 1-0050: rk628_is_avi_ready PDEC_AVI_PB:0x10000840, avi_rcv_rdy:0
rk628d 1-0050: SCDC_REGS1:0x80000f00, act:1920x1080, total:2200x1125, fps:60,

pixclk:148500000

rk628-csi-v4l2 1-0051: DVI mode detected

diff --git a/drivers/media/i2c/rk628/rk628_csi_v4l2.c b/drivers/media/i2c/rk628/rk628_csi_v4l2.c
index 32182d4433605..36568f5a081e0 100644

--- a/drivers/media/i2c/rk628/rk628_csi_v4l2.c
+++ b/drivers/media/i2c/rk628/rk628_csi_v4l2.c
@@ -1347,7 +1347,7 @@ static void rk628_csi_initial_setup(struct v4l2_subdev *sd)
      def_edid.start_block = 0;
      def_edid.blocks = 2;
      if (csi->rk628->version >= RK628F_VERSION)
-          def_edid.edid = rk628f_edid_init_data;
+          def_edid.edid = edid_init_data;
      else
           def_edid.edid = edid_init_data;
      rk628_csi_s_edid(sd, &def_edid);

v4l2-ctl -d /dev/video0 --set-fmt-
video=width=1920,height=1080,pixelformat=NV12 --stream-mmap=3`

rkisp1: MIPI mis error:

rkisp-vir0: MIPI error: overflow: 0x00000001

rkisp1 ff910000.rkisp1: CIF_ISP_PIC_SIZE_ERROR

 - entity 70: m00_b_rk628-csi rk628-csi (1 pad, 1 link)
       type V4L2 subdev subtype Sensor
       device node name /dev/v4l-subdev3

pad0: Source
   [fmt:UYVY2X8/1280x720]
   -> "rockchip-csi2-dphy0":0 []

strcat(video_name, "/dev/v4l-subdev2");

strcat(video_name, "/dev/v4l-subdev3");

AndroidRuntime: java.lang.UnsatisfiedLinkError: dlopen failed: library
"/system/lib64/libhdmiinput_jni.so" needed or dlopened by

"/apex/com.android.runtime/lib64/libnativeloader.so" is not accessible for
the namespace "classloader-namespace"

HdmiInput-navtive: openDevice(113): open /dev/v4l-subdev2
failed,erro=Permission denied

$ dumpsys media.camera

== Service global info: ==


Number of camera devices: 1
Number of normal camera devices: 1

09-29 04:43:30.673 405 405 W ServiceManagement: Waited one second for
android.hardware.camera.provider@2.4::ICameraProvider/legacy/0. Waiting

another...
09-29 04:43:31.673 405 405 W ServiceManagement: Waited one second for
android.hardware.camera.provider@2.4::ICameraProvider/legacy/0. Waiting
another...
...
09-29 04:43:31.904 1404 1404 F DEBUG : backtrace:
09-29 04:43:31.904 1404 1404 F DEBUG : #00 pc 0007214e
/vendor/lib/hw/camera.rk30board.so
(android::camera2::ChromeCameraProfiles::handleAndroidStaticMetadata(char const*,
char const**)+546)
09-29 04:43:31.904 1404 1404 F DEBUG : #01 pc 00007895 /system/lib/vndk-
28/libexpat.so (doContent+432)
09-29 04:43:31.905 1404 1404 F DEBUG : #02 pc 0000637b /system/lib/vndk-

28/libexpat.so (contentProcessor+40)
09-29 04:43:31.905 1404 1404 F DEBUG : #03 pc 00003825 /system/lib/vndk-
28/libexpat.so (XML_ParseBuffer+84)
09-29 04:43:31.905 1404 1404 F DEBUG : #04 pc 000711ad
/vendor/lib/hw/camera.rk30board.so
(android::camera2::CameraProfiles::getDataFromXmlFile()+148)
09-29 04:43:31.905 1404 1404 F DEBUG : #05 pc 00071e97
/vendor/lib/hw/camera.rk30board.so
(android::camera2::ChromeCameraProfiles::init()+86)
09-29 04:43:31.905 1404 1404 F DEBUG : #06 pc 000734c7
/vendor/lib/hw/camera.rk30board.so (android::camera2::PlatformData::init()+198)
09-29 04:43:31.905 1404 1404 F DEBUG : #07 pc 000cecb3

/vendor/lib/hw/camera.rk30board.so (initCameraHAL()+46)
...

hardware/rockchip/camera
--- a/etc/camera/camera3_profiles_rk3399.xml
+++ b/etc/camera/camera3_profiles_rk3399.xml

@@ -769,7 +769,7 @@

 <!-- ******************PSL specific section end
**************************************************************-->
   </Profiles>
-  <Profiles cameraId="0" name="rk628-csi" moduleId="m00">
+  <Profiles cameraId="0" name="rk628-csi-v4l2" moduleId="m00">

09-24 10:21:20.154 1552 1570 E AndroidRuntime: FATAL EXCEPTION: Thread-2
09-24 10:21:20.154 1552 1570 E AndroidRuntime: Process:

com.android.rockchip.camera2, PID: 1552
09-24 10:21:20.154 1552 1570 E AndroidRuntime: java.lang.IllegalStateException:
startRecording() called on an uninitialized AudioRecord.
09-24 10:21:20.154 1552 1570 E AndroidRuntime: at
android.media.AudioRecord.startRecording(AudioRecord.java:983)
09-24 10:21:20.154 1552 1570 E AndroidRuntime: at
com.android.rockchip.camera2.AudioStream$recordSound.run(AudioStream.java:199)
09-24 10:21:20.154 1552 1570 E AndroidRuntime: at
java.lang.Thread.run(Thread.java:764)
09-24 10:21:20.164 464 820 W ActivityManager: Force finishing activity
com.android.rockchip.camera2/.RockchipCamera2
09-24 10:21:20.183 1552 1552 D RockchipCamera2: onPause

packages/apps/rkCamera2
--- a/AndroidManifest.xml

+++ b/AndroidManifest.xml
@@ -4,7 +4,8 @@
   package="com.android.rockchip.camera2">

      <uses-permission android:name="android.permission.CAMERA" />
-     <uses-permission
android:name="android.permission.WRITE_EXTERNAL_STORAGE" />
+     <uses-permission android:name="android.permission.WRITE_EXTERNAL_STORAGE"
/>
+     <uses-permission android:name="android.permission.RECORD_AUDIO" />
   <application
      android:allowBackup="true"
      android:icon="@mipmap/ic_launcher"

diff --git a/src/com/android/rockchip/camera2/RockchipCamera2.java b/src/com/android/rockchip/camera2/RockchipCamera2.java
index 9dc29b8..02ee104 100755
--- a/src/com/android/rockchip/camera2/RockchipCamera2.java
+++ b/src/com/android/rockchip/camera2/RockchipCamera2.java
@@ -100,9 +100,11 @@ public class RockchipCamera2 extends Activity {
      if (ActivityCompat.checkSelfPermission(this,
         Manifest.permission.CAMERA) != PackageManager.PERMISSION_GRANTED
         && ActivityCompat.checkSelfPermission(this,
-             Manifest.permission.WRITE_EXTERNAL_STORAGE) !=
PackageManager.PERMISSION_GRANTED) {
+             Manifest.permission.WRITE_EXTERNAL_STORAGE) !=

PackageManager.PERMISSION_GRANTED
+        && ActivityCompat.checkSelfPermission(this,
+             Manifest.permission.RECORD_AUDIO) !=
PackageManager.PERMISSION_GRANTED) {
         ActivityCompat.requestPermissions(RockchipCamera2.this,
-          new String[] { Manifest.permission.CAMERA,
Manifest.permission.WRITE_EXTERNAL_STORAGE },
+          new String[] { Manifest.permission.CAMERA,

Manifest.permission.WRITE_EXTERNAL_STORAGE, Manifest.permission.RECORD_AUDIO},
           REQUEST_CAMERA_PERMISSION);
         return;
      }

setprop persist.vendor.camera.hal.debug 5

I RkCamera: <HAL> RKISP2GraphConfig: @addLinkParams, srcName:rockchip-csi2-dphy0, srcPad:1, sinkName:none, sinkPad:0, enable:1, flags:1
I RkCamera: <HAL> RKISP2GraphConfig: @addLinkParams, srcName:none, srcPad:1, sinkName:none, sinkPad:0, enable:1, flags:1
I RkCamera: <HAL> RKISP2GraphConfig: @addLinkParams, srcName:none, srcPad:2, sinkName:rkisp_rawwr0, sinkPad:0, enable:1, flags:1
I RkCamera: <HAL> RKISP2GraphConfig: @addLinkParams, srcName:none, srcPad:4, sinkName:rkisp_rawwr2, sinkPad:0, enable:1, flags:1
I RkCamera: <HAL> RKISP2GraphConfig: @addLinkParams, srcName:none, srcPad:5, sinkName:rkisp_rawwr3, sinkPad:0, enable:1, flags:1
I RkCamera: <HAL> RKISP2GraphConfig: @addFormatParams, entityName:none, width:1920, height:1080, pad:0, format:0x2006:V4L2_MBUS_FMT_UYVY8_2X8, field:0
I RkCamera: <HAL> RKISP2GraphConfig: @addSelectionParams, width:1920, height:1080, left:0, top:0, target:0, pad:0, entityName:none
I RkCamera: <HAL> RKISP2GraphConfig: @addSelectionParams, width:1920, height:1080, left:0, top:0, target:0, pad:2, entityName:none
I RkCamera: <HAL> RKISP2GraphConfig: @addFormatParams, entityName:none, width:1920, height:1080, pad:2, format:0x2008:V4L2_MBUS_FMT_YUYV8_2X8, field:0
I RkCamera: <HAL> RKISP2GraphConfig: @addLinkParams, srcName:none, srcPad:3, sinkName:none, sinkPad:0, enable:1, flags:1
I RkCamera: <HAL> RKISP2GraphConfig: @addLinkParams, srcName:none, srcPad:0, sinkName:none, sinkPad:1, enable:1, flags:1
D RkCamera: <HAL> RKISP2GraphConfig: @ isNeedPathCrop : stream ratios: 1.777778
D RkCamera: <HAL> RKISP2GraphConfig: @ isNeedPathCrop : mp_need_crop 1, sp_need_crop 0, sp_enabled 0
D RkCamera: <HAL> RKISP2GraphConfig: @ calc_crop : src_ratio:1.777778, dst_ratio:1.777778, src(1920x1080), dst(1920x1080)
I RkCamera: <HAL> RKISP2GraphConfig: @addSelectionVideoParams, width:1920, height:1080, left:0, top:0, target:0, type:1, flags:0 entityName:none
I RkCamera: <HAL> RKISP2GraphConfig: @addFormatParams, entityName:none, width:1920, height:1080, pad:0, format:0x3231564e:V4L2_PIX_FMT_NV12, field:0
I RkCamera: <HAL> RKISP2GraphConfig: @addLinkParams, srcName:none, srcPad:2, sinkName:none, sinkPad:0, enable:1, flags:1
I RkCamera: <HAL> RKISP2GraphConfig: @getImguMediaCtlConfig : No need for selfPath

diff --git a/psl/rkisp2/RKISP2GraphConfig.cpp b/psl/rkisp2/RKISP2GraphConfig.cpp
index 2a5fa5a..3d2409c 100755
--- a/psl/rkisp2/RKISP2GraphConfig.cpp

+++ b/psl/rkisp2/RKISP2GraphConfig.cpp
@@ -76,6 +76,7 @@ const string MEDIACTL_POSTVIEWNAME = "postview";

 const string MEDIACTL_STATNAME = "rkisp1-statistics";
 const string MEDIACTL_VIDEONAME_CIF = "stream_cif_dvp_id0";
+const string MEDIACTL_VIDEONAME_CIF_MIPI_ID0 = "stream_cif_mipi_id0";

 RKISP2GraphConfig::RKISP2GraphConfig() :
      mManager(nullptr),
@@ -2620,6 +2621,13 @@ status_t RKISP2GraphConfig::getImguMediaCtlConfig(int32_t
cameraId,
            addLinkParams("rkisp-isp-subdev", 2, "rkisp_mainpath", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);

            addLinkParams("rkisp-isp-subdev", 2, "rkisp_selfpath", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
         }
+     } else if(mipName2.find("mipi") != std::string::npos) {
+        addLinkParams(mipName, mipSrcPad, mipName2, csiSinkPad, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);

+        addLinkParams(mipName2, 1, "stream_cif_mipi_id0", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
+        addLinkParams(mipName2, 2, "stream_cif_mipi_id1", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
+        addLinkParams(mipName2, 3, "stream_cif_mipi_id2", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
+        addLinkParams(mipName2, 4, "stream_cif_mipi_id3", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
+        mSensorLinkedToCIF = true;
      } else {
         addLinkParams(mipName, mipSrcPad, csiName, csiSinkPad, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);

         addLinkParams(csiName, csiSrcPad, IspName, ispSinkPad, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
@@ -2628,6 +2636,12 @@ status_t RKISP2GraphConfig::getImguMediaCtlConfig(int32_t
cameraId,
         addLinkParams(csiName, 5, "rkisp_rawwr3", 0, 1,
MEDIA_LNK_FL_ENABLED, mediaCtlConfig);
      }
   }
+  if(mSensorLinkedToCIF){
+     addImguVideoNode(IMGU_NODE_VIDEO, MEDIACTL_VIDEONAME_CIF_MIPI_ID0,
mediaCtlConfig);
+     addFormatParams(MEDIACTL_VIDEONAME_CIF_MIPI_ID0, mCurSensorFormat.width,
mCurSensorFormat.height,

+           0, V4L2_PIX_FMT_NV12, 0, 0, mediaCtlConfig);
+     return OK;
+  }
   // isp input pad format and selection config
   addFormatParams(IspName, ispInWidth, ispInHeight, ispSinkPad, ispInFormat,
0, 0, mediaCtlConfig);
   addSelectionParams(IspName, ispInWidth, ispInHeight, 0, 0,
V4L2_SEL_TGT_CROP, ispSinkPad, mediaCtlConfig);

rk628_gpio_direction_output(rk628, GPIO1_B1, GPIO_REG_HIGH);
rk628_gpio_direction_output(rk628, GPIO1_B2, GPIO_REG_HIGH)；

rk628_pinctrl_set_mux(rk628, GPIO1_B1, DDCM0SDARX);
rk628_pinctrl_set_mux(rk628, GPIO1_B2, DDCM0SCLRX)；

# cat /proc/asound/cards
 1 [rockchiphdmiin ]: rockchip_hdmiin - rockchip,hdmiin
                rockchip,hdmiin

rk3399:/ # cat /sys/kernel/debug/asoc/components
...
dummy-codec

ff8a0000.i2s
ff8a0000.i2s
ff880000.i2s
ff880000.i2s
...
rk3399:/ # cat /sys/kernel/debug/asoc/dais
...
ff8a0000.i2s
ff880000.i2s
dummy-codec
....

--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi

@@ -1788,6 +1788,7 @@
           clocks = <&cru SCLK_I2S2_8CH>, <&cru HCLK_I2S2_8CH>;
           resets = <&cru SRST_I2S2_8CH>, <&cru SRST_H_I2S2_8CH>;
           reset-names = "reset-m", "reset-h";
+          rockchip,capture-only;
           power-domains = <&power RK3399_PD_SDIOAUDIO>;
           status = "disabled";

pinctrl-names = "default";
pinctrl-0 = <&rk628_rst>, <&clk_testout2>;
assigned-clocks = <&cru SCLK_TESTCLKOUT2>;

assigned-clock-rates = <24000000>;
clocks = <&cru SCLK_TESTCLKOUT2>;
clock-names = "soc_24M";

&pinctrl {
      test {
           clk_testout2: clk_testout2 {

           rockchip,pins = <0 8 RK_FUNC_3 &pcfg_pull_none>;
      };
};

pinctrl-names = "default";
pinctrl-0 = <&test_clkout>;
assigned-clocks = <&cru SCLK_TESTOUT_SRC>;

assigned-clock-parents = <&xin24m>;
clocks = <&cru SCLK_TESTOUT>;
clock-names = "soc_24M";

&pinctrl {
      test {
           test_clkout: test-clkout {

                 rockchip,pins = <0 17 RK_FUNC_1 &pcfg_pull_none>;
           };
      };
};

&i2c2_rk628 {
   pinctrl-names = "default";
   pinctrl-0 = <&rk628_reset &refclk_pins>;

   assigned-clocks = <&pmucru CLK_WIFI>;
   assigned-clock-rates = <24000000>;
   clocks = <&pmucru CLK_WIFI>;
   clock-names = "soc_24M";
};

&pinctrl {
   rk628 {
      rk628_reset: rk628-reset {
         rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
      };
   };

};

&pinctrl {
   ......

   refclk {
      /omit-if-no-ref/
      refclk_pins: refclk-pins {
         rockchip,pins =
           /* refclk_ou */
           <0 RK_PA0 1 &pcfg_pull_none>;
      };
   };
   ......
};

&i2c1 {
   status = "okay";


   rk628_csi_v4l2: rk628_csi_v4l2@50 {
      compatible = "rockchip,rk628-csi-v4l2";
      reg = <0x50>;
      //clocks = <&ext_cam_clk>;
      //clock-names = "xvclk";

      interrupt-parent = <&gpio4>;
      interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_irq>;
      //power-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_LOW>;

      plugin-det-gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
      rockchip,camera-module-index = <0>;
      rockchip,camera-module-facing = "back";
      rockchip,camera-module-name = "RK628-CSI";
      rockchip,camera-module-lens-name = "NC";
      port {
         rk628_out: endpoint {
           remote-endpoint = <&hdmi2mipi_in>;
           data-lanes = <1 2 3 4>;
         };
      };
   };

};

&mipi_dphy_rx0 {
   status = "okay";

   ports {
      #address-cells = <1>;
      #size-cells = <0>;

      port@0 {
         reg = <0>;
         #address-cells = <1>;
         #size-cells = <0>;


         hdmi2mipi_in: endpoint@1 {
           reg = <1>;
           remote-endpoint = <&rk628_out>;
           data-lanes = <1 2 3 4>;
         };
      };

      port@1 {
         reg = <1>;
         #address-cells = <1>;
         #size-cells = <0>;


         dphy_rx0_out: endpoint@0 {
           reg = <0>;
           remote-endpoint = <&isp0_mipi_in>;
         };
      };
   };
};

&rkisp1_0 {
   status = "okay";


   port {
      #address-cells = <1>;
      #size-cells = <0>;

      isp0_mipi_in: endpoint@0 {
         reg = <0>;
         remote-endpoint = <&dphy_rx0_out>;
      };
   };
};

&i2c4 {
   status = "okay";


   rk628_csi_v4l2_1: rk628_csi_v4l2_1@50 {
      compatible = "rockchip,rk628-csi-v4l2";
      reg = <0x50>;
      //clocks = <&ext_cam_clk>;
      //clock-names = "xvclk";

      interrupt-parent = <&gpio3>;
      interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_irq1>;
      //power-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
      reset-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_LOW>;

      plugin-det-gpios = <&gpio0 RK_PD7 GPIO_ACTIVE_LOW>;
      rockchip,camera-module-index = <1>;
      rockchip,camera-module-facing = "front";
      rockchip,camera-module-name = "RK628-CSI";
      rockchip,camera-module-lens-name = "NC";
      port {
         rk628_out1: endpoint {
           remote-endpoint = <&hdmi2mipi_in1>;
           data-lanes = <1 2 3 4>;
         };
      };
   };
};

&mipi_dphy_tx1rx1 {

   status = "okay";

   ports {
      #address-cells = <1>;
      #size-cells = <0>;

      port@0 {
         reg = <0>;
         #address-cells = <1>;
         #size-cells = <0>;

         hdmi2mipi_in1: endpoint@1 {

           reg = <1>;
           remote-endpoint = <&rk628_out1>;
           data-lanes = <1 2 3 4>;
         };
      };

      port@1 {
         reg = <1>;
         #address-cells = <1>;
         #size-cells = <0>;

         dphy_tx1rx1_out: endpoint@0 {
           reg = <0>;

           remote-endpoint = <&isp1_mipi_in>;
         };
      };
   };
};

&rkisp1_1 {
   status = "okay";

   port {
      #address-cells = <1>;
      #size-cells = <0>;


      isp1_mipi_in: endpoint@0 {
         reg = <0>;
         remote-endpoint = <&dphy_tx1rx1_out>;
      };
   };
};

</Profiles>
<Profiles cameraId="0" name="rk628-csi" moduleId="m00">
    <Supported_hardware>
        <hwType value="SUPPORTED_HW_RKISP1"/>
    </Supported_hardware>

</Profiles>
<Profiles cameraId="1" name="rk628-csi" moduleId="m01">
    <Supported_hardware>
        <hwType value="SUPPORTED_HW_RKISP1"/>
    </Supported_hardware>

diff --git a/common/platformdata/PlatformData.cpp b/common/platformdata/PlatformData.cpp

index 36d2ac9..d3fcb4b 100755
--- a/common/platformdata/PlatformData.cpp
+++ b/common/platformdata/PlatformData.cpp
@@ -1047,7 +1047,7 @@ CameraHWInfo::CameraHWInfo() :
   mProductName = "<not_set>";
   mManufacturerName = "<not set>";
   mCameraDeviceAPIVersion = CAMERA_DEVICE_API_VERSION_3_3;
-  mSupportDualVideo = false;
+  mSupportDualVideo = true;
   mSupportExtendedMakernote = false;
   mSupportFullColorRange = true;
   mSupportIPUAcceleration = false;

&i2c1 {
   status = "okay";


   rk628_csi_v4l2: rk628_csi_v4l2@50 {
      compatible = "rockchip,rk628-csi-v4l2";
      reg = <0x50>;
      //clocks = <&ext_cam_clk>;
      //clock-names = "xvclk";

      interrupt-parent = <&gpio4>;
      interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
      pinctrl-names = "default";
      pinctrl-0 = <&rk628_irq>;
      //power-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;

      reset-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_LOW>;
      plugin-det-gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
      rockchip,camera-module-index = <0>;
      rockchip,camera-module-facing = "back";
      rockchip,camera-module-name = "RK628-CSI";
      rockchip,camera-module-lens-name = "NC";
      port {
         rk628_out: endpoint {
            remote-endpoint = <&hdmi2mipi_in>;
            data-lanes = <1 2 3 4>;
         };
      };

   };
};

&mipi_dphy_rx0 {
   status = "okay";

   ports {
      #address-cells = <1>;
      #size-cells = <0>;

      port@0 {
         reg = <0>;
         #address-cells = <1>;

         #size-cells = <0>;

         hdmi2mipi_in: endpoint@1 {
            reg = <1>;
            remote-endpoint = <&rk628_out>;
            data-lanes = <1 2 3 4>;
         };
      };

      port@1 {
         reg = <1>;
         #address-cells = <1>;

         #size-cells = <0>;

         dphy_rx0_out: endpoint@0 {
            reg = <0>;
            remote-endpoint = <&isp0_mipi_in>;
         };
      };
   };
};

&rkisp1_0 {
   status = "okay";


   port {
      #address-cells = <1>;
      #size-cells = <0>;
      isp0_mipi_in: endpoint@0 {
         reg = <0>;

         remote-endpoint = <&dphy_rx0_out>;
      };
   };
};